• Ideal probe for up to 48 V power conversion
  • 250, 500 MHz and 1 GHz bandwidth
  • 80 V dynamic range
  • 60 V common mode
• Highest accuracy
  • 0.5% gain accuracy
  • Precision gain calibration
  • Best LF flatness (0.1 dB)
• Lowest noise and highest rejection
• Wide variety of tips
  • High performance solder-in
  • Browser
  • Single pins and header
  • Mini and micro grabbers
  • Socketed connections
  • High temp solder-in
  • Y-banana adaptor
• ProBus active probe interface

The ZS Series probes provide high impedance and an extensive set of probe tips and ground accessories to handle a wide range of probing scenarios. The high 1 MΩ input resistance and low 0.9 pF input capacitance means this probe is ideal for all frequencies. The ZS Series probes provide full system bandwidth with all Teledyne LeCroy oscilloscopes with bandwidths of 4 GHz and lower.

• Up to 4 GHz Bandwidth 
• ±60 V Offset Capability 
• ±800 mV Dynamic Range 
• 50 kΩ DC Input Impedance 
• 1.2x Attenuation for low additive noise 
• MCX terminated cable with wide variety of connections: 
  • Solder-in (4 GHz) 
  • Coaxial Cable to U.FL receptacle (3 GHz) 
  • MCX PCB Mount (4 GHz) 
  • Browser (500 MHz) 
• ProBus Interface

Fully Integrated: With the ProBus™ interface, the AP033 becomes an integral part of the oscilloscope. The probe sensitivity and offset can be controlled from the oscilloscope front panel, the probe front panel, or by using remote control commands (GPIB or RS-232). Sensitivity, offset, input capacitance, and common mode voltage range are displayed on the oscilloscope screen. When used with a LeCroy digital oscilloscope, no external power supply is required.

• Easy to Use
  • No need to break the circuit or insert a shunt
  • Small form factors for use on crowded boards
• Variety of Applications
  • Bandwidths up to 100 MHz
  • Peak currents up to 700 A
  • Sensitivities down to 1mA/div
• High Precision Measurements
  • Low frequency accuracy of 1%
  • Integrated autozero capability
• Fully Integrated with Teledyne LeCroy Oscilloscope
  • No additonal hardware is required
  • Power is supplied from oscilloscope ProBus connection
  • Automatic display of waveforms in Amps and calculated power traces scaled correctly in Watts
  • Degauss and Autozero directly from oscilloscope user interface
• DCS025 Deskew Calibration Source
  • Provides ability to precisely deskew most voltage probes along with 30, 150 and 500A current probes

Differential active probes are like two probes in one. Instead of measuring a test point in relation to a ground point (like single-ended active probes), differential probes measure the difference in voltage of a test point in relation to another test point

• Choice of 4 GHz or 6 GHz bandwidth models
• Up to 5 Vpk-pk dynamic range with low noise
• ±3 V offset range
• Low loading and high impedance for minimal signal disturbance
• Ideal for DDR2, DDR3, LPDDR2
• Deluxe soft carrying case
• Innovative QuickLink architecture
• Wide variety of tips and leads
  • Solder-In Lead
  • Optional Positioner (Browser) Tip
  • Quick Connect Lead
  • Square Pin Lead
  • HiTemp Solder-In Lead

• Bandwidth models from 8 GHz to 30 GHz
• Low loading and high impedance for minimal signal disturbance
• Wide variety of tips:
  • Standard and high-sensitivity 30 GHz solder-in tips
  • High-temperature solder-in tip with 1-meter lead
  • QuickLink adapter for mixed-signal probing
  • Handheld browser tip
  • Tips for direct oscilloscope connection to CrossSync PHY protocol analyzer interposers
• Built-in tip identification for simple setup and precise signal reproduction
• Ideal for debug and validation of:
  • PCIe 1.0 to 6.0
  • DDR3/LPDDR3
  • DDR4/LPDDR4/LPDDR4X
  • DDR5
  • Other high-speed serial interfaces

High voltage differential probes provide high CMRR over a broad frequency range (up to 400 MHz) to simplify the measurement challenges found in noisy, high common-mode power electronics environments. The probe’s design is easy-to-use and enables safe, precise high voltage floating measurements.