Teledyne LeCroy - Active Voltage Rail Probe
- Up to 4 GHz Bandwidth
- ±60 V Offset Capability
- ±800 mV Dynamic Range
- 50 kΩ DC Input Impedance
- 1.2x Attenuation for low additive noise
- MCX terminated cable with wide variety of connections:
- Solder-in (4 GHz)
- Coaxial Cable to U.FL receptacle (3 GHz)
- MCX PCB Mount (4 GHz)
- Browser (500 MHz)
- ProBus Interface
Voltage rail probes are designed specifically to probe a 50 Ohm DC power/voltage rail. The probe has large built-in offset, low attenuation (noise), and high DC input impedance. Built-in offset and low attenuation permit the power/voltage rail to be offset in the oscilloscope by its mean DC voltage with high oscilloscope gain (sensitivity) to achieve a noise-free view of small signal variations. The high DC input impedance eliminates loading of the DC rail.
|
RP2060 |
RP4060 |
|
|---|---|---|
|
Bandwidth |
2 GHz |
4 GHz |
|
Risetime |
220 ps |
110 ps |
|
Offset Range |
+/- 60 V |
+/- 60 V |
|
Input Dynamic Range |
+/- 800 mV |
+/- 800 mV |
|
Attenuation |
1.2x |
1.2x |
|
Non-Destruct Voltage |
+/- 100 V |
+/- 100 V |
|
DC Input Resistance |
50 kΩ |
50 kΩ |
|
Active Voltage Rail Probe |
|
|---|---|
|
Power/Voltage Rail Probe. 2 GHz bandwidth, 1.2x attenuation, +/-60V offset, +/-800mV Includes a complete set of solder-in leads and coaxial cables. Browser tip sold separately |
|
|
Power/Voltage Rail Probe. 4 GHz bandwidth, 1.2x attenuation, +/-30V offset, +/-800mV Includes a complete set of solder-in leads, coaxial cables, and PCB mounts. Limited Availability |
|
|
Power/Voltage Rail Probe. 4 GHz bandwidth, 1.2x attenuation, +/-60V offset, +/-800mV Includes a complete set of solder-in leads and coaxial cables. Browser tip sold seperately |
|
|
RP2060/RP4060 Browser Tip accessory. Includes 0 Ohm (1x), 450 Ohm (10x) and 950 Ohm (20x) tips. |
|
|
Qty 3 MCX 4 GHz solder-in lead accessories (additional to those supplied with rail probe) 18cm long |
|
More Product Information
-
Easy to operate/calibrate
-
Annual calibration Lightweight / portable
-
Rechargeable battery or externally powered
-
Percent of battery capacity displayed
-
Self-test on power-up
-
Measures DC voltage Manual or Auto Ranging
-
2 and 3 Wire Meggar
-
Compliant with Boeing Spec 10-61959 Rev H
-
MIL-STD-810 Method 511.4 certified
-
Traceable to NIST
-
Tests any AC or DC capacitive fuel, water, LOX/engine oil or other AC capacitive system*
- Four operating modes: – CC, CV, CR, CP
- Static, Dynamic and Sequence mode support
- Built in Application Functions - Short Circuit Test, Battery Test Mode, CR-LED Mode, OCP and OPP Test
- Provides a load of up to 300 Watts
- Programmable and analog external control
-
Software-driven design allows for field updates for adding new features, capability or modifications due to industry changes
-
TCAS and ADS-B Target Generator
-
Simulates 32 dynamic/400 static intruders
-
ADS-B squitter encode/decode
-
More test capability than any tester in the market, all packed into one box
-
Pulse and frequency measurement Transponder test option for Modes A, C, S
-
Optional Command set emulation for SDX-2000, ATC-1400A and S-1403DL
-
10.4 inch touch screen LCD display for operator control of all test set capabilities or can be remotely controlled via GPIB or Ethernet
-
Four port antenna simulation
-
Hybrid surveillance
-
Six independent transmitters and two receivers
-
Data parsing for analysis
- Available in 30MHz, 40MHz, 60MHz, 80MHz, 120MHz, 200MHz, 350MHz and 500MHz models
- All models feature 2 channels
- Max Sampling rate of 150 Msa/s (30MHz & 60 MHz) 1.2 Gsa/s (40MHz, 80MHz, 120MHz) and 2.4 Gsa/s (200MHz, 350MHz and 500MHz) models.
- Up to 16-bit vertical resolution (14-bit on 30MHz & 60MHz models).
- All models have 4.3" Touchscreens.
- Excellent analog and digital modulation types available (AM, DSB-AM, FM, PM, PSK, FSK, ASK and PWM)
- All Digital IF technology
- 10.1” WVGA (1024 x 600) Display
- Frequency range from 9 KHz up to 3.2 GHz
- -161 dBm/Hz Displayed Average Noise Level (Typ)
- -98 dBc/Hz @ 10 khz Offset Phase Noise (Typ)
- Total Amplitude Accuracy < 0.7 dB
- 1 Hz Minimum Resolution Bandwidth (RBW)
- Comes with Preamplifier
High voltage differential probes provide high CMRR over a broad frequency range to simplify the measurement challenges found in noisy, high common-mode power electronics environments. The probe’s design is easy-to-use and enables safe, precise high voltage floating measurements.
- 150 MHz, 2 analog channels
- 8 synchronized digital channels (T3AWG2152-D only)
- 16-bit vertical resolution
- 128 MPts @Ch waveform memory
- Max sampling rate of 600 MS/s
- Available in 250 MHz and 350 MHz models
- 2, 4 and 8 channel modes
- 16-bit vertical resolution
- Max Sampling rate of 1.2 GS/s
- Max sinewave frequency of 250 MHz and 350 MHz respectively
- Provides a passive PCIe® backplane for test applications
- Self-contained, portable and self-powered
- Supplies power for +3.3V, +3.3Vaux and +12V rails
- Generates PCIe reference clock
- Accepts external clock inputs
- Generates valid PERST# bus reset that can be activated by manual push button
- Includes two mid-bus probe footprints for traffic monitoring
- Supports two PCIe x16 sockets which accept cards of any link width (x1, x4, x8, x16)
- Provides indication of valid connection of PRSNT1# and PRSNT2# lines for each card
- Supports data rates of 2.5 GT/s and 5.0 GT/s
Teledyne LeCroy
Teledyne LeCroy is a leading provider of oscilloscopes, protocol analyzers and related test and measurement solutions that enable companies across a wide range of industries to design and test electronic devices of all types. Since our founding in 1964, we have focused on creating products that improve productivity by helping engineers resolve design issues faster and more effectively.
Oscilloscopes are tools used by designers and engineers to measure and analyze complex electronic signals in order to develop high-performance systems and to validate electronic designs in order to improve time to market. Protocol analyzers are tools used by designers and engineers to generate and monitor traffic over high speed serial data interfaces, including DDR, PCI Express, Fibre Channel, Serial ATA, SAS, USB and others. Both products are critical in the development of a wide variety of demanding design applications.
We utilize both of these important product areas in combination to tackle the most demanding serial data test applications, offering tailored solutions to help our customers perfect their chips, interfaces, subsystems and products which utilize these important communications standards. With the explosion in the use of serial data communications technologies in semiconductors, between devices on circuit boards and between computers and peripherals, we are aimed at a growing and important market.
Our oscilloscopes offer a powerful combination of large and informative displays combined with advanced waveshape analysis capabilities typically tailored to enhance the productivity of engineers in specific applications areas such as serial data test, disk drive test and automotive bus analysis.
Headquartered in Chestnut Ridge, New York, LeCroy has sales, service and development subsidiaries in the US and throughout Europe and Asia. LeCroy products are employed across a wide variety of industries, including semiconductor, computer, consumer electronics, military/aerospace, automotive/industrial, and telecommunications.
Contact Details
Headquarters Teledyne LeCroy
700 Chestnut Ridge Road, Chestnut Ridge, NY 10977-6499, USA
Phone: 800-553-2769 or 845-425-2000
Phone Support: 1-800-553-2769
Fax Sales: 845-578-5985
Email Sales: contact.corp@teledynelecroy.com
Email Support: support@teledynelecroy.com (Oscilloscopes, Waveform Generators, Signal Integrity)
Test & Measurement
Download Line Card
Document
