Teledyne LeCroy - MDA 8000HD 350 MHz - 2 GHz Motor Drive Analyzer
- Static power analysis - like a dedicated power analyzer
- Dynamic power analysis – capture more information
- Complete test coverage – control system, power section, motor
- Comprehensive mechanical interface
- Harmonics calculation option
- Vector display option (THREEPHASEVECTOR)
- Waveform Transformations option (THREEPHASEdq0)
- 16 Channels with OscilloSYNC™
The Motor Drive Analyzer is built on an 8 channel, 12-bit resolution oscilloscope platform. It acquires any signal and performs three-phase electrical and mechanical power calculations. It provides complete power section and embedded control test coverage.
Static Power Analysis
The mean-value Numerics table displays voltage, current, power, speed, torque, etc. values for short (or long) time periods during constant load, speed and torque operating conditions - just like what a dedicated power analyzer instrument provides.
Dynamic Power Analysis
Capture thousands of power cycles over long time periods. Per-cycle Waveform views help you understand dynamic behaviors. Use Zoom+Gate to isolate and correlate power behaviors to control system operation during dynamic load, speed, and torque operating conditions.
Complete Test Coverage
Acquire and display analog, digital and serial data signals from both power and embedded control systems. Correlate power system behaviors to control system activity during time periods as short as a single device switching cycle.
Comprehensive Mechanical Interface
Nine speed, four angle, and five torque sensors supported – most supported only by the Motor Drive Analyzer. Calculate mechanical power at your bench without external sensors connected.
Harmonics Calculation Option
Rigorous software DFT method precisely separates desired frequency content. Provides THD numeric calculation and per-cycle Waveforms, harmonic order table and spectral displays (up to nine simultaneous).
3-phase Vector Display Option
Two simultaneous vector displays permit visualization of three-phase system voltage and current. Vector information can be harmonically filtered and is compatible with Zoom+Gate to show vector changes during dynamic or long acquisitions.
Waveform Transformations option (THREEPHASEdq0)
Support for two simultaneous αβγ (Clarke) and dq0 (Park) real-time transformations with X-Y plot capability available for d vs. q and α vs. β components
16 Channels with OscilloSYNC™
View and control 16 analog channels on a single display with OscilloSYNC Oscilloscope Synchronization. Setup is incredibly easy – it’s like having a single 16-channel acquisition system with the benefit of being able to use each oscilloscope or MDA independently.
|
Main Specifications |
|
|---|---|
|
Bandwidth |
350 MHz - 2 GHz |
|
Max Sampling Rate |
10 GS/s |
|
Resolution |
12-bit |
|
Input Channels |
8 |
|
Memory |
50 Mpts - 5 Gpts |
|
Max Memory |
5 Gpts |
|
MDA 8038HD (350 MHz Bandwidth, 8 Input Channels, 50 Mpts/ch, 10GS/s) |
|
|---|---|
|
Bandwidth |
350 MHz |
|
Sample Rate |
10 GS/s on 8 Ch with ESR |
|
Maximum Acquisition Memory |
5 Gpts (2 Ch operation) |
|
Input Channels |
8 |
|
Vertical Resolution |
12 bits |
|
MDA 8058HD (500 MHz Bandwidth, 8 Input Channels, 50 Mpts/ch, 10GS/s) |
|
|---|---|
|
Bandwidth |
500 MHz |
|
Sample Rate |
10 GS/s on 8 Ch with ESR |
|
Maximum Acquisition Memory |
5 Gpts (2 Ch operation) |
|
Input Channels |
8 |
|
Vertical Resolution |
12 bits |
|
MDA 8108HD (1 GHz Bandwidth, 8 Input Channels, 50 Mpts/ch, 10GS/s) |
|
|---|---|
|
Bandwidth |
1 GHz |
|
Sample Rate |
10 GS/s on 8 Ch with ESR |
|
Maximum Acquisition Memory |
5 Gpts (2 Ch operation) |
|
Input Channels |
8 |
|
Vertical Resolution |
12 bits |
|
MDA 8208HD (2 GHz Bandwidth, 8 Input Channels, 50 Mpts/ch, 10GS/s) |
|
|---|---|
|
Bandwidth |
2 GHz |
|
Sample Rate |
10 GS/s on 8 Ch with ESR |
|
Maximum Acquisition Memory |
5 Gpts (2 Ch operation) |
|
Input Channels |
8 |
|
Vertical Resolution |
12 bits |
More Product Information
-
Teledyne e2v Sapphire CMOS sensor
-
Switchable shutter modes
-
Power over Ethernet
-
60 fps at full resolution
-
Monochrome (G-192B) and color (G-192C) models
-
GigE Vision interface with Power over Ethernet
-
Screw mount RJ45 Ethernet connector for secure operation in industrial environments
-
Supports cable lengths up to 100 meters (CAT-6 recommended)
-
Comprehensive I/O functionality for simplified system integration
-
Popular C-Mount lens mount
-
Easy camera mounting via standard M3 threads on top and bottom of housing or optional tripod adapter
-
Easy software integration with Allied Vision's Vimba Suite and compatibility to the most popular third party image-processing libraries.
-
Defect pixel masking feature with the Defect Mask Loader tool that allows you to manage a user defined defective pixel list to match your application and optimize the life cycle of the camera.
-
Select between B 270 ASG protection glass and filter types: Jenofilt 217 IR cut filter, Hoya C-5000 IR cut filter, RG715 IR pass filter, or RG830 IR pass filter
High voltage differential probes provide high CMRR over a broad frequency range to simplify the measurement challenges found in noisy, high common-mode power electronics environments. The probe’s design is easy-to-use and enables safe, precise high voltage floating measurements.
-
Compact probe head
-
Supports fine pitch SMD probing
-
Rugged, Sharp tip
-
HF optimized connection accessories
-
Over 30 accessories
-
Low input capacitance
With the ProBus interface, the ZD500, 1000, and 1500 becomes an integral part of the oscilloscope. All probe gain and offset controls are transparent to the user, making it easier to probe the circuit without concern for which gain setting to choose. When used with a LeCroy digital oscilloscope, no external power supply is required.
- Vector Network Analyzer Frequency Range from 10 MHz up to 3.2 GHz
- Spectrum Analyzer Frequency Range from 9 kHz up to 3.2 GHz
- -156 dBm/Hz Displayed Average Noise Level (Typ.)
- -98 dBc/Hz @10 kHz Offset Phase Noise (1 GHz, Typ.)
- Total Amplitude Accuracy < 1.2 dB
- 1 Hz Minimum Resolution Bandwidth (RBW)
- All-Digital IF Technology
- Standard Preamplifier
- Distance to fault capability using VNA time domain analysis
- Up to 1.5 GHz Tracking Generator Kit
- Built-in Advanced Measurement capability (CHP, ACPR, OBW, CNR, TOI, etc)
- 10.1 lnch WVGA (1024 x 600) Display
- Static power analysis - like a dedicated power analyzer
- Dynamic power analysis – capture more information
- Complete test coverage – control system, power section, motor
- Comprehensive mechanical interface
- Harmonics calculation option
- Vector display option (THREEPHASEVECTOR)
- Waveform Transformations option (THREEPHASEdq0)
- 16 Channels with OscilloSYNC™
Fully Integrated: With the ProBus™ interface, the AP033 becomes an integral part of the oscilloscope. The probe sensitivity and offset can be controlled from the oscilloscope front panel, the probe front panel, or by using remote control commands (GPIB or RS-232). Sensitivity, offset, input capacitance, and common mode voltage range are displayed on the oscilloscope screen. When used with a LeCroy digital oscilloscope, no external power supply is required.
- Up to 20 GHz bandwidth and 80 GS/s sample rate
- The most advanced oscilloscope user interface
- The industry’s only true hardware 14.1 Gb/s serial trigger
- Low Jitter Measurement Floor and exceptional timebase stability
- Comprehensive set of serial data analysis, debug, validation and compliance tools
- Integrated 50 Ω and 1 MΩ inputs for true connection and probing flexibility
- Integrated standard and custom measurements and math functions for unrivaled analysis capability
- Multi-lane serial data eye, jitter and crosstalk analysis
- Real-time de-embedding, emulation, and equalization
- Provides a passive PCIe® backplane for test applications
- Self-contained, portable and self-powered
- Supplies power for +3.3V, +3.3Vaux and +12V rails
- Generates PCIe reference clock
- Accepts external clock inputs
- Generates valid PERST# bus reset that can be activated by manual push button
- Includes two mid-bus probe footprints for traffic monitoring
- Supports two PCIe x16 sockets which accept cards of any link width (x1, x4, x8, x16)
- Provides indication of valid connection of PRSNT1# and PRSNT2# lines for each card
- Supports data rates of 2.5 GT/s and 5.0 GT/s
Teledyne LeCroy
Teledyne LeCroy is a leading provider of oscilloscopes, protocol analyzers and related test and measurement solutions that enable companies across a wide range of industries to design and test electronic devices of all types. Since our founding in 1964, we have focused on creating products that improve productivity by helping engineers resolve design issues faster and more effectively.
Oscilloscopes are tools used by designers and engineers to measure and analyze complex electronic signals in order to develop high-performance systems and to validate electronic designs in order to improve time to market. Protocol analyzers are tools used by designers and engineers to generate and monitor traffic over high speed serial data interfaces, including DDR, PCI Express, Fibre Channel, Serial ATA, SAS, USB and others. Both products are critical in the development of a wide variety of demanding design applications.
We utilize both of these important product areas in combination to tackle the most demanding serial data test applications, offering tailored solutions to help our customers perfect their chips, interfaces, subsystems and products which utilize these important communications standards. With the explosion in the use of serial data communications technologies in semiconductors, between devices on circuit boards and between computers and peripherals, we are aimed at a growing and important market.
Our oscilloscopes offer a powerful combination of large and informative displays combined with advanced waveshape analysis capabilities typically tailored to enhance the productivity of engineers in specific applications areas such as serial data test, disk drive test and automotive bus analysis.
Headquartered in Chestnut Ridge, New York, LeCroy has sales, service and development subsidiaries in the US and throughout Europe and Asia. LeCroy products are employed across a wide variety of industries, including semiconductor, computer, consumer electronics, military/aerospace, automotive/industrial, and telecommunications.
Contact Details
Headquarters Teledyne LeCroy
700 Chestnut Ridge Road, Chestnut Ridge, NY 10977-6499, USA
Phone: 800-553-2769 or 845-425-2000
Phone Support: 1-800-553-2769
Fax Sales: 845-578-5985
Email Sales: contact.corp@teledynelecroy.com
Email Support: support@teledynelecroy.com (Oscilloscopes, Waveform Generators, Signal Integrity)
Test & Measurement
Download Line Card
Document
