Sorensen - XPH Series - 175W - 420W Compact, high performance low cost DC Benchtop power supply
- Low noise
- Excellent line⁄load regulation
- Coarse and fine voltage controls
- Constant voltage or constant current operation with automatic crossover and mode indication
- Individual ON⁄Off switch per output (not including fixed output)
- Switchable 3.3V⁄5V output on triple output model
- Switchable remote sense (XPH 1810 and XPH 4210 models)
The Sorensen XPH Series benchtop DC power supply provides 175 to 420 watts of DC power. The XPH is a compact, high-performance low-cost power supply suited for benchtop applications.
The Sorensen XPH Series lab power supply uses combined switch–mode pre–regulation with linear post-regulation to provide performance comparable with an all-linear design.
The XPH benchtop power supply features excellent line and load regulation with low noise and good transient response. The XPH Series is available in a single, dual, and triple output for benchtop use.
The Sorensen XPH dual output models have two independent and isolated outputs with their own on–off switch. The outputs can be wired in either series or parallel to provide higher voltage and higher current output. All outputs are intrinsically short-circuiting proof and are protected against external voltages and reverse currents. The XPH triple output model has the same features as the dual output model with an additional switchable fixed output of 3.3V and 5V.
Document
More Product Information
High resistance decade with built-in test signal meter for calibration of high resistance meters up to 6 kV. Based on M6xx Real-Resistance decade series with short function for short current testing.
- 10 kΩ - 100.0 GΩ, short function
- Hot-switching up to 6 kVdc limit
- Test voltage and current indication
- Multiple voltage⁄current ranges
- Direct numeric entry and incremental rotary control of voltage and current
- The remote or local sense
- Illuminated keys and display legends.
- Up to ten store/recall set-ups (30 setups for triple output)
- Power output display
- Link and copy mode
- Available in 30MHz, 40MHz, 60MHz, 80MHz, 120MHz, 200MHz, 350MHz and 500MHz models.
- All models feature 2 channels.
- Max Sampling rate of 150 Msa/s (30MHz & 60 MHz) 1.2 Gsa/s (40MHz, 80MHz, 120MHz) and 2.4 Gsa/s (200MHz, 350MHz and 500MHz) models.
- Up to 16-bit vertical resolution (14-bit on 30MHz & 60MHz models).
- All models have 4.3" Touchscreens.
- Excellent analog and digital modulation types available (AM, DSB-AM, FM, PM, PSK, FSK, ASK and PWM).
- Industry Leading Power Density – Up to 1500 Watts in 1U
- Standard Digital Interfaces – USB&RS232/485
- LXI Ethernet and Isolated analog interfaces
- Power Factor Correction-PFC and universal AC input
- “Green” Sleep Mode – Automatically “sleeps” after period of non-use
- Built in sequencing - Unload your system controller
- Programmable fold-back protection delay
- Precise programming of voltage and current slew rate for sensitive loads.
- Industrial field bus interfaces (Modbus-TCP, Modbus-RTU, Ethernet) enable real-time digital control.
- Built-in power quality monitoring detects and saves input voltage anomalies which can be saved for later diagnostic analysis.
- Programmable analog interface scaling facilitates integrating the ASD FLX with existing systems easily.
- Built-in energy meter calculates the delivered energy throughout a process or period.
- Optional real-time clock enables accurate timestamping of events.
1.35 mm DC to 90 GHz connectors from Southwest Microwave include a field-replaceable 4-hole Flange-mount Connector, standard Thread-in Connector, Cable Connector, clamp-on solderless End Launch Connector, Solderless Vertical Launch Connector, and between series adaptors.
- All Digital IF technology
- 10.1” WVGA (1024 x 600) Display
- Frequency range from 9 KHz up to 3.2 GHz
- -161 dBm/Hz Displayed Average Noise Level (Typ)
- -98 dBc/Hz @ 10 khz Offset Phase Noise (Typ)
- Total Amplitude Accuracy < 0.7 dB
- 1 Hz Minimum Resolution Bandwidth (RBW)
- Comes with Preamplifier
- High Power Density: 600 watts in 1U (1.75 inches) high, half rack (8.5 inches) wide; no top or bottom clearance spacing required.
- Near Linear Ripple & Noise Ripple as low as 2.5mV rms, noise as low as 15mV p-p.
- Remote Control
- LXI Compliant Ethernet LAN / RS-232C (16 bit)
- IEEE-488.2 / RS-232C (12 bit)
- Standard analog programming 0-5V, 0-10V, or 0-5kΩ.
- Comprehensive Test Solutions - Our CTS 4.0 Series offers complete test solutions for emissions and immunity compliance testing of AC and DC power products, ensuring your products are ready for global markets.
- Single & Three Phase Operation - Offers flexibility
- Direct PC Bus Access - Provides high sampling rate and resolution for accurate measurements and high-speed data transfers
- PC-Based Harmonic & Flicker Testing - Provides real-time full-color data display updates and continuous PASS/FAIL monitoring
- Supports Global Standards - Supports European and Japanese standards
- Easy To Use Interface - Provides IEC test setup, data analysis, display, MS Word test reports, and data files generated in MS Excel format
- High Resolution - Data storage to disk for post-acquisition analysis and reporting
- Single Step - Single Step and Fast Forward replay of recorded test data at 200 mSec
AMETEK Programmable Power
Located in San Diego, California, AMETEK Programmable Power designs, manufactures, and markets precision, AC and DC programmable power supplies, electronic loads, application specific power subsystems, and compliance test solutions for customers requiring and valuing differentiated power products and services. Also part of our business is VTI Instruments, which delivers precision modular instrumentation and systems for electronic signal distribution, acquisition, and monitoring, used in the world's most demanding test applications.
AMETEK Programmable Power boasts one of the industries' broadest portfolios of programmable power products under the well-known and respected Sorensen, Elgar, and California Instruments brands. AMETEK Programmable Power’s products serve a wide range of stimulus (T&M) and process power needs in applications including semiconductor fabrication, commercial and defense ATE, oil exploration, solar array and battery string simulation, avionics, general R&D and EMC compliance testing.
VTI Instruments provides products and systems which are used to monitor and record data that characterizes the physical integrity and performance of aircraft, engines, and other large structures, as well as automate the functional testing of complex electronic systems. VTI Instruments is recognized as an industry leader with a reputation of providing reliable data, first time, every time.
With strong brands, a broad product portfolio, exceptional precision power conversion and control expertise, proven power system integration capabilities and deep applications knowledge, AMETEK Programmable Power is your source for programmable power supplies, precision data acquisition instruments, and more.
Contact Details
AMETEK Programmable Power, Inc. − San Diego
9250 Brown Deer Road, San Diego, CA 92121, USA
Phone: 858-450-0085
Fax: 858-458-0267
Email: sales.ppd@ametek.com for general inquiries
Test & Measurement
Download Line Card
