NEO NXB - 20820 Voltage / Current Breakout Test Box
-
On-Off power switch
-
20 A Circuit Breaker
-
Inlet - NEMA L6-20
-
Outlets – NEMA L6-20R
-
3ft.
-
(2) fork terminals (current)
-
(1) fork terminals (ground)
-
(2) Shielded Banana (voltage)
Single output for passthrough to test rack. Tester pigtail interface simplifies connecting to a variety of voltage/current measuring systems.
Voltage | Current | Input | Output | Test Output | Switch/Breaker |
208 | 20A | L6-20 - Cord | L6-20 R | Pigtail | Yes |
More Product Information
Model FM7004A is an E-field control center that offers monitoring, display, and alarm capabilities for immunity-test environments. Exceptionally precise with auto-recognition to adapt to laser powered probes. The FM7004A is self-calibrating and is programmed to be self-correcting. The unit allows field-strength measurement at up to four probe locations simultaneously with results displayed on a backlit color LCD. Choose from any field probe with sensitivity from 0.4 to 1000 V/m, 0.012 – 17 A/m, and frequency response from 5 kHz to 60 GHz.
- 24-bit, delta-sigma ADC, simultaneous sampling
- Programmable Sample Rate up to 128kSPS
- Full, Half & Quarter Bridge with 120Ω, 350Ω & 1kΩ bridge completion
- Voltage Excitation: 0.5V to 10V
- Current Excitation: 0.46mA
- 2-Wire & 4-Wire Ohms/RTD
- Bridge Zero Balancing
- Built-In-Self-Test (BIST)
- Strain Lead Wire Calibration
- Shunt Calibration: 50kΩ, 100kΩ & External provided by User
- TEDS Support
- LXI Ethernet Interface
- IEEE-1588 Synchronization
- Power over Ethernet (PoE) or 10–50 V DC input
- Built-in Parallel Data Streaming
- Full-featured Embedded Web Interface
- Compact 1U Half-rack Form Factor
- Up to 96 differential channels per full rack mainframe
- Constantly monitor input signals for fault conditions
- Flexible configurations for detecting edges, out-of-bounds conditions and measuring pulse widths
- Inputs can be masked, inverted, and combined to produce interrupts
- Can be used as a time stamp module and as a digital I/O
- Programmable debounce circuitry prevents erroneous readings
- 10 V and 100 V input ranges
- On-board memory stores events with IEEE 1588 timestamps
- Synchronize reading of input states with other scanned analog channels
-
On-Off power switch
-
15 A Circuit Breaker
-
Inlet - IEC C14 for use with any cordset
-
Outlets – (8) IEC C13
-
3ft.
-
(2) fork terminals (current)
-
(1) fork terminals (ground)
-
(2) Shielded Banana (voltage)
- Two 120/240 V Outlets
- Circuitry rated for 20 A
- 8’ Flexible Power Cord
- Shrouded Safety Banana Jacks
- Stable footprint with non-slip feet
Our “A” and “W” Series amplifiers have the power to deliver all the field strength you need. With unsurpassed mismatch capabilities and excellent flatness, they provide all the power promised over the entire operating band.
We subject our amplifiers to the harshest conditions just to make sure they give you reliable service and performance over the long haul. We test them under various output VSWR loads to stress them to the limit. The only problem we ran into was that there were no available loads to handle the enormous power up to 80,000 W that our amplifiers deliver. Whereas this would stop most manufacturers, it presented another challenge to our talented designers, and we designed our own. All our RF solid-state amplifiers have modulation capability that will faithfully reproduce AM, FM or Pulse Modulation appearing on the input signal for use in the most demanding EMC applications.
These technologically advanced amplifiers perform beyond the norm, beyond expectations, and way beyond the abilities of other test amplifiers.
These self-contained, broadband, completely solid-state amplifiers are designed for applications requiring the ultimate in output power over a wide instantaneous bandwidth with high gain. Extensive control and status reporting capabilities are available both locally and remotely. Most models feature air-cooled designs while some higher power units feature liquid cooled designs. The touch-screen panels are intuitive, convenient, and easy to use.
NEO
NEO offers a line-up of Power measurement breakout boxes designed for use with Yokogawa's precision power analyzers.