Sorensen - DLM 3-4 kW Programmable DC Power Supplies

Overview
Specifications & Details
Datasheets & Downloads
Videos

High Power Density : 3 kW and 4 kW models, 2U (3½” high), (19” wide); no top or bottom clearance spacing required
Preview Push-button : Overvoltage protection (OVP), voltage and current preview buttons
Remote Voltage Sense : Sense leads are easily connected to a solderless connector
Parallel or Series Operation Field configurable
Power Factor Correction ≥0.98 1 Ф 3kW

Manufactured By: AMETEK Programmable Power

The Sorensen DLM 3kW and 4kW Series programmable DC power supplies are designed to provide highly stable, continuously variable DC output voltage and current for a broad range of applications in a compact 2U (3½” high) chassis.

The 3 kW and 4 kW 2U rackmount DC power supply models have output voltages from 0-5 VDC to 0-600 VDC and a current range from 0-5A to 0-450A. The output rms noise is as low as 10 mV. The output will recover to 1% of its steady-state voltage within 1ms for a step load change of 100% to 70% or 70% to 100%. The front panel layout makes the series extremely easy to use. Control switches include power on, enable/ standby, and local/ remote.

Displays and indicators show programmed set points and operational control status. The programmed voltage, current, and overvoltage set points are displayed with two large 3½ digit LED displays. Operational Status LEDs indicate power on, shutdown, over temperature, overvoltage, constant current, and voltage mode status. Control Status LEDs indicate front panel lockout, remote control, and standby status. IEEE- 488.2 control LEDs indicate the error, service request, and remote address status.

The 3 kW DC Power Supply Models will accept 200*/230 VAC single phase and 200*/208 VAC three phase input power.

The 4 kW DC Supply Models will accept 200*/208 VAC, three-phase, or optional 400 or 480 VAC three-phase input power.

*Operating temperature below 40°C

Features and Benefits

High Power Density DC Power Supply

3 kW and 4 kW models, 2U (3½ inches) high, 19 inches wide; no top or bottom clearance spacing required.

Wide Range of DC Output Voltages

3 kW and 4 kW outputs 0-5V, 8V, 16V, 32V, 40V, 60V, 80V, 150V, 300V and 600V

Preview Pushbutton

Overvoltage protection (OVP), voltage and current preview buttons allow viewing these set points at any time with or without the output enabled.

Remote Voltage Sense

Sense leads are easily connected to a solderless connector.

Remote Operation

Standard analog programming
Output enable/disable remotely.
Optional IEEE-488.2 and RS 232
Optional optically isolated analog programming

Calibration

All models can be calibrated without removing the covers.

Operating Modes

Constant voltage and constant current, with LED indicators

Parallel or Series Operation

Field configurable

Input Power Factor

0.95 typical (three phase for all models) 0.98 typical (single phase)

CE Mark

5 Year Warranty

Sorensen DLM Series Specifications

Common
Front Panel Controls	Knobs with 3½ digit digital displays to control output voltage and current settings. Power on/off switch, output enable/standby switch and local/remote switch. Voltage, current and overvoltage preview push buttons allow you to preview the programmed settings at any time; overvoltage limit is adjusted with a set screw accessible through the front panel.
Displays and Indicators	Voltage and overvoltage setting 3½ digit LED display, current setting 3½ digit LED display. LED indicators for power on, shutdown, remote, overvoltage protection, overtemperature and front panel lockout, constant voltage and constant current modes. IEEE-488.2 indicators include error, SRQ and address (M9E option).
Overvoltage Protection	Output overvoltage (resets by cycling the enable/standby switch)
Cooling	Internal fans with over temperature protection

Rear Panel Control/Monitor
Remote Sense	The maximum load line drop is up to the full voltage rating of the supply. The drop in the load leads subtracts from the maximum voltage available for the load except as follows: maximum rated voltage is available at the load and voltage regulation specifications apply for line drops of <2V for models rated 5V to 16V, and <5V for all other models.
Remote Sense Protection	Unit will not be damaged due to misconnection of the remote sense leads
Remote Programming	Voltage, current (0-100%) and OVP (5-110%) of full scale can be programmed by selectable 0-5 VDC, 0-10 VDC, or 0-5 kΩ.
Remote Monitoring	Voltage or current can be monitored with user-selectable ranges, 0-5 VDC or 0-10 VDC
Operational Features	Master/slave parallel operation, up to 2 units can be connected in parallel with active current sharing control to within 10% of each supply. Series operation, up to 3 units of the same model type can be connected in series (consult manual). Negative terminal rated at 150 Vmax above ground
Software	LabVIEW® driver M9E/M85
Regulatory Compliance	CE Mark, 16-185 & 22-180 certified NRTL to EN 61010-1.

Environmental
Operating Temperature	0°C to 50°C, no derating (<200 VAC range limited to 40°C maximum)
Storage Temperature	-40°C to 65°C

Physical
Dimensions	Width: 19” (483 mm) Height: 3.5” (88 mm) Depth: 18” (508 mm)
Weight	40 lbs. ( 18.2 kg )
Shipping Weight	49 lbs. ( 22.3 kg )

Input
	3 kW	4 kW
Voltage Ranges	180-264 VAC, 47-63 Hz, (<200 VAC range limited to 40°C maximum)	180-264 VAC, 345-455 VAC, 432-528 VAC, 47-63 Hz (<200 VAC range limited to 40°C maximum)
Phases	single or three phase	three phase
Power Factor	0.95 typical with three phase input, 0.98 typical with single phase input	0.95 typical with three phase input
Current	single phase, 21A rms; three phase, 12A rms	180-264 VAC, 15A rms; 345-455 VAC, 8.5A rms; 432-528 VAC, 6.5A rms;

Output
Stability	±0.05% of maximum voltage or current over 8 hours after 15 minute warm-up time at fixed line, load and temperature. Current accuracy for 5V, 8V, and 16V models is 1% typical.
Line Regulation	For input voltage variation over the AC input voltage range, with constant rated load. Voltage: 0.05% of maximum rated output +2mV Current: 0.1% of maximum rated output
Load Regulation	For 0-100% load variation, with constant nominal line voltage. Voltage: 0.05% of maximum rated output +2mV Current: 0.1% of maximum rated output
Voltage Regulation	0.05% of maximum rated output +2mV
Transient Response	Typically recovers in 1.5 ms to within 1% of steady-state output voltage (greater than 50% of Vmax) for 70-100% or 100-70% load change.
Temperature Coefficient	0.02%/°C of rated output voltage; 0.03%/°C of rated output current. Change in output per °C change in ambient temperature, with constant line and load.
Efficiency	5-8V Models: 82% typical 16-80V Models: 87% typical 150-600V Models: 85% typical (at maximum output power)

Output
3kW Models	Voltage	Current
DLM 5-350E	0-5	0-350
DLM 8-350E	0-8	0-350
DLM 16-185E	0-16	0-185
DLM 32-95E	0-32	0-95
DLM 40-75E	0-40	0-75
DLM 60-50E	0-60	0-50
DLM 80-37E	0-80	0-37
DLM 150-20E	0-150	0-20
DLM 300-10E	0-300	0-10
DLM 600-5E	0-600	0-5
4kW Models	Voltage	Current
DLM 5-450E	0-5	0-450
DLM 8-450E	0-8	0-450
DLM 16-250E	0-16	0-250
DLM 22-180E *	0-22	0-180
DLM 32-125E	0-32	0-125
DLM 40-100E	0-40	0-100
DLM 60-66E	0-60	0-66
DLM 80-50E	0-80	0-50
DLM 150-26E	0-150	0-26
DLM 300-13E	0-300	0-13
DLM 600-6.6E	0-600	0-6.6
* 22V Model available as 4kW

Output : Voltage and Current
Model	Output Rating
Model	Voltage (VDC)	Current (ADC)
DLM 5-350E	0-5	0-350
DLM 5-450E	0-5	0-450
DLM 8-350E	0-8	0-350
DLM 8-450E	0-8	0-450
DLM 16-185E	0-16	0-185
DLM 16-250E	0-16	0-25
DLM 22-180E *	0-22	0-180
DLM 32-95E	0-32	0-95
DLM 32-125E	0-32	0-125
DLM 40-75E	0-40	0-75
DLM 40-100E	0-40	0-100
DLM 60-50E	0-60	0-50
DLM 60-66E	0-60	0-66
DLM 80-37E	0-80	0-37
DLM 80-50E	0-80	0-50
DLM 150-20E	0-150	0-20
DLM 150-26E	0-150	0-26
DLM 300-10E	0-300	0-10
DLM 300-13E	0-300	0-13
DLM 600-5E	0-600	0-5
DLM 600-6.6E	0-600	0-6.6
* 22V Model available as 4kW

Output
Model	Regulation Line and Load
Model	Voltage (0.05% of Vmax + 2mV)	Current (0.1% of Imax)
DLM 5-350E	5 mV	350 mA
DLM 5-450E	5 mV	450 mA
DLM 8-350E	6 mV	350 mA
DLM 8-450E	6 mV	450 mA
DLM 16-185E	10 mV	185 mA
DLM 22-180E *	13 mV	180 mA
DLM 16-250E	10 mV	250 mA
DLM 32-95E	18 mV	95 mA
DLM 32-125E	18 mV	125 mA
DLM 40-75E	22 mV	75 mA
DLM 40-100E	22 mV	100 mA
DLM 60-50E	32 mV	50 mA
DLM 60-66E	32 mV	66 mA
DLM 80-37E	42 mV	37 mA
DLM 80-50E	42 mV	50 mA
DLM 150-20E	77 mV	20 mA
DLM 150-26E	77 mV	26 mA
DLM 300-10E	152 mV	10 mA
DLM 300-13E	152 mV	13 mA
DLM 600-5E	302 mV	55 mA
DLM 600-6.6E	302 mV	7 mA
* 22V Model available as 4kW

Output
Model	Meter Accuracy
Model	Voltage (0.5% of Vmax + 1 Count)	Current (0.75% of Imax + 1 Count)
DLM 5-350E	0.04 V	4 A
DLM 5-450E	0.04 V	5 A
DLM 8-350E	0.05 V	4 A
DLM 8-450E	0.05 V	5 A
DLM 16-185E	0.09 V	3 A
DLM 16-250E	0.09 V	3 A
DLM 22-180E *	0.2 V	3 A
DLM 32-95E	0.3 V	0.8 A
DLM 32-125E	0.3 V	1 A
DLM 40-75E	0.3 V	0.7 A
DLM 40-100E	0.3 V	0.9 A
DLM 60-50E	0.4 V	0.5 A
DLM 60-66E	0.4 V	0.6 A
DLM 80-37E	0.5 V	0.4 A
DLM 80-50E	0.5 V	0.5 A
DLM 150-20E	0.9 V	0.3 A
DLM 150-26E	0.9 V	0.3 A
DLM 300-10E	1.6 V	0.09 A
DLM 300-13E	1.6 V	0.11 A
DLM 600-5E	3.1 V	0.05 A
DLM 600-6.6E	3.1 V	0.06 A
* 22V Model available as 4kW

Output
Model	Preview Accuracy		OVP Adjustment Range (5% to 110% of Vmax)
Model	Voltage (0.05% of Vmax +1 count)	Current ( 1.0% of Imax +1 count)	OVP Adjustment Range (5% to 110% of Vmax)
DLM 5-350E	0.04 V	5 A	0.3-5.5 V
DLM 5-450E	0.04 V	6 A	0.3-5.5 V
DLM 8-350E	0.05 V	5 A	0.4-8.8 V
DLM 8-450E	0.05 V	6 A	0.4-8.8 V
DLM 16-185E	0.09 V	3 A	0.8-17.6 V
DLM 16-250E	0.09 V	4 A	0.8-17.6 V
DLM 22-180E *	0.2 V	3 A	1.1-24.2 V
DLM 32-95E	0.3 V	1.1 A	1.6-35 V
DLM 32-125E	0.3 V	1.4 A	1.6-35 V
DLM 40-75E	0.3 V	0.9 A	2-44 V
DLM 40-100E	0.3 V	1.1 A	2-44 V
DLM 60-50E	0.4 V	0.6 A	3-66 V
DLM 60-66E	0.4 V	0.8 A	3-66 V
DLM 80-37E	0.5 V	0.5 A	4-88 V
DLM 80-50E	0.5 V	0.6 A	4-88 V
DLM 150-20E	0.9 V	0.3 A	7.5-165 V
DLM 150-26E	0.9 V	0.4 A	7.5-165 V
DLM 300-10E	1.6 V	0.11 A	15-330 V
DLM 300-13E	1.6 V	0.14 A	15-330 V
DLM 600-5E	3.1 V	0.06 A	30-660 V
DLM 600-6.6E	3.1 V	0.08 A	30-660 V

Output
Model	Ripple and Noise
Model	Ripple (RMS)*	Noise (P-P)
DLM 5-350E	12 mV	100 mV
DLM 5-450E	12 mV	100 mV
DLM 8-350E	12 mV	100 mV
DLM 8-450E	12 mV	100 mV
DLM 16-185E	10 mV	100 mV
DLM 16-250E	10 mV	100 mV
DLM 22-180E	10 mV	100 mV
DLM 32-95E	10 mV	100 mV
DLM 32-125E	10 mV	100 mV
DLM 40-75E	10 mV	100 mV
DLM 40-100E	10 mV	100 mV
DLM 60-50E	15 mV	100 mV
DLM 60-66E	15 mV	100 mV
DLM 80-37E	15 mV	120 mV
DLM 80-50E	15 mV	120 mV
DLM 150-20E	30 mV	200 mV
DLM 150-26E	30 mV	200 mV
DLM 300-10E	60 mV	300 mV
DLM 300-13E	60 mV	300 mV
DLM 600-5E	100 mV	500 mV
DLM 600-6.6E	100 mV	500 mV

J3 Connector
1	Remote Output Enable	14	Remote Shutdown Input (+). Positive or negative true logic selection with S1
2	Remote Shutdown Return (-)	15	+5 VDC Auxiliary Output
3	Remote OVP Programming Input	16	1 mA Current Source for OVP Programming
4	Remote Programming Indicator	17	OVP Status Indicator
5	Operating Mode Indicator	18	Overtemperature Shutdown Indicator
6	Status Indicator Return (-)	19	DC Voltage Monitor Output
7	Current Monitor Output	20	Remote /Local Voltage Control Select
8	Not Used	21	1 mA Current Source for Voltage Programming
9	Voltage Programming Input	22	1 mA Current Source for Current Programming
10	Current Programming Input	23	Remote/Local Current Control Select
11	Not Used	24	Not Used
12	Programming/Monitor Return (-)	25	Not Used
13	Not Used
* 22V Model available as 4kW

AMETEK DLM 3kW 4kW Series Datasheet.pdf

Manuals, Software, Drivers and Other

View YouTube Channel

AMETEK Programmable Power

https://www.programmablepower.com/

Located in San Diego, California, AMETEK Programmable Power designs, manufactures, and markets precision, AC and DC programmable power supplies, electronic loads, application specific power subsystems, and compliance test solutions for customers requiring and valuing differentiated power products and services. Also part of our business is VTI Instruments, which delivers precision modular instrumentation and systems for electronic signal distribution, acquisition, and monitoring, used in the world's most demanding test applications.

AMETEK Programmable Power boasts one of the industries' broadest portfolios of programmable power products under the well-known and respected Sorensen, Elgar, and California Instruments brands. AMETEK Programmable Power’s products serve a wide range of stimulus (T&M) and process power needs in applications including semiconductor fabrication, commercial and defense ATE, oil exploration, solar array and battery string simulation, avionics, general R&D and EMC compliance testing.

VTI Instruments provides products and systems which are used to monitor and record data that characterizes the physical integrity and performance of aircraft, engines, and other large structures, as well as automate the functional testing of complex electronic systems. VTI Instruments is recognized as an industry leader with a reputation of providing reliable data, first time, every time.

With strong brands, a broad product portfolio, exceptional precision power conversion and control expertise, proven power system integration capabilities and deep applications knowledge, AMETEK Programmable Power is your source for programmable power supplies, precision data acquisition instruments, and more.