-
The LL158 Series produces an oblique (30°) line of illumination for line scan applications in a passively cooled design.
-
When oriented across a moving web or conveyor line, unlike standard line lights, this linear light’s unique geometry highlights engraved or raised lines that run parallel to the material travel.
-
Provides an intensity level of 53kLux (working distance of 75mm).
-
Pre-engineered for expandability in 6” (152mm) increments up to 90” (2.28m).
-
Available intensity control provides illuminance adjustability for every 6″ increment via a 0 – 10v input.
Sorensen - PLA Series Air-Cooled Programmable DC Electronic Loads
- Broadest Model Selection: 800W to 7.5kW (higher power available up to 250kW Contact Factory)
- Exclusive Voltage Models: 60V to 1000V
- Multiple loads in one: Multiple ranges for voltage, current resistance and power
- Intuitive Front Panel Control: Run sequences, triggers, constant current to constant power cross over
- RoHS Compliant
Traditional DC Electronic Load Solutions are bulky and large. Most are offered with standard voltage, current and power ratings. In the ATE world, rack space is a highly coveted asset, and application demands are constantly diversifying with new technology development.
AMETEK Programmable Power's PLA Series of Air-cooled DC electronic loads offers the industry’s smallest footprint, the highest power density, and current rating, along with the broadest selection of high voltage models on the market. PLA Air-cooled DC electronic loads are capable of being custom-tailored to meet your application requirements.
View our PLA and PLW Series Infographic here.
Features And Benefits
Closed-case Calibration
With the Air-cooled DC electronic load line, there’s no longer a need to send your electronic load back to the factory for calibration or remove dozens of screws to reach a potentiometer.
Simply follow the calibration routine from the front panel and you should be back up and running in a very short period (some electronic test equipment is needed). This will virtually eliminate downtime and eradicate the annual cost associated with shipping your Air-cooled DC electronic load back to the factory for calibration.
Individual FET Protection
To ensure the reliability of the PLA Series Air-cooled DC electronic load, the design includes individual FET protection. A programmable electronic load may contain many FETs in parallel, which can create a cascading failure if one of them was to short out.
The PLA Air-cooled DC electronic load design isolates failures so other components will not be affected or stressed, increasing the system’s level of protection against catastrophic failure. With individual FET protection, the MTTR is reduced, and the electronic load quickly returns to full operation.
Ultra-low Voltage Operation
The PLA Air-cooled DC electronic load design allows the programmable electronic load to operate at voltage levels approaching .1V. They will typically dissipate full rated current below 1% of their maximum rated voltage.
For example, a 60V unit designed to dissipate 1500A will allow the user to operate at .6V and still dissipate the full amount.
|
Model |
PLA |
|---|---|
|
Voltage |
160-1000 VDC |
|
Current |
10-1500 ADC |
|
Power |
800 W-7.5 kW |
|
Overview |
Air-cooled programmable DC electronic load |
Document
Document
Document
Document
More Product Information
Vimba is our future-proof platform-independent SDK for all Allied Vision cameras with GigE Vision, USB3 Vision, IEEE 1394, and Camera Link interface. With Vimba, you can acquire images and control your Allied Vision camera instantly, but also program complex vision applications or connect to third-party libraries.
Highlights
-
Proven technology: designed in conjunction with several top STM groups in the world
-
Quiet, low vibration operation
-
Low running costs and reduced maintenance
-
Easy operation and fast cool-down; load sample when the system is cold for TL models
-
Calibrated RuO and CMN thermometry read by model 372S resistance bridge are installed on the mixing chamber plate
-
High-density, compact (1U) precision data acquisition instruments
-
LXI™ LAN connectivity
-
Fully integrated signal conditioning maximizes performance and accuracy
-
Easily integrate thermocouples, voltages, RTDs, thermistors, frequency, strain and pressure on an per-channel basis
-
Distributed, synchronized measurements over the wire
-
Scalable architecture easily expands from tens to thousands of channels
-
DC version available for test cells requiring closer proximity to test article
-
End-to-end self-calibration ensures optimum runtime performance
-
Web-based access for monitoring and control
-
Exlab turnkey software for simplified setup, control and data display
-
IMX304 CMOS sensor
-
ALVIUM image processing
-
MIPI CSI-2 interface
-
Various hardware options
-
Monochrome (1800 C-1236m) and color (1800 C-1236c) models
-
ALVIUM® Technology for on-board image processing
-
MIPI CSI-2 interface with up to 4 lanes
-
Platform concept that enables the operation of different Alvium camera models with a common software
-
Hirose HR FHH55 FPC connector with minimum space requirements for a compact design
-
Precise sensor-to-lens mount alignment
-
Standard M3 mounting holes for top and bottom mounting, standard M2 mounting holes for front mounting
-
Industrial performance for embedded vision applications
-
Easy-to-install driver and code examples
Transmission line probes are a special type of passive probe designed for use at very high frequencies. They replace the high impedance probe cable found in a traditional passive probe with a precision transmission line, with a characteristic impedance that matches the oscilloscope input (50 Ohm). This greatly reduces the input capacitance to a fraction of a picofarad, minimizing the loading of high frequency signals. A matching network at the tip increases the DC input resistance. While they have lower DC input resistance than a traditional passive probe (usually 500 Ohm) to 1kOhm), the input impedance of these probes remains nearly constant over their entire frequency range. A traditional /10 passive probe will have a 10 MOhm) input impedance at DC, however this impedance drops rapidly with frequency, passing below the input impedance of a transmission line probe at less than 100 MHz.
Focus Microwaves’ DELTA series of electro-mechanical tuners is designed specifically for high frequency on wafer measurements. The tuner’s low profile allows it to be placed within the wafer perimeter and allows for a direct connection between the probe tip and the tuner, eliminating all possible insertion loss between the DUT and the tuner. This revolutionary new tuner design enables the engineer to achieve optimum tuning range, with a tuner whose footprint and weight has been dramatically reduced.
-
AR0135CS CMOS sensor
-
ALVIUM image processing
-
USB3 Vision
-
Various hardware options
-
Monochrome (1800 U-120m) and color (1800 U-120c) models
-
ALVIUM® Technology for on-board image processing
-
USB3 Vision interface for GenICam SFNC features
-
Platform concept that enables the operation of different Alvium camera models with a common software
-
Micro-B USB 3.1 Gen 1 connector with screw locks for industrial applications
-
Precise sensor-to-lens mount alignment
-
Standard M3 mounting holes for top and bottom mounting, standard M2 mounting holes for front mounting
-
Industrial performance for both embedded and machine vision applications
Thin plate broadband antenna has been developed for efficient immunity testing against hand-held transmitters and cellular phones. Many pieces of spot frequency antennas had to be used in turn thus fur. This new Thin-plate Broadband Antenna is a single antenna solution eliminating the need for antenna changes and dramatically reducing the test time. Furthermore, this antenna with its small-size and lightweight properties and a flexible handle is suitable for testing in narrow spaces.
-
A wide frequency range eliminating the need for antenna changes
-
30W maximum power input allows high filed strengths
-
High efficiency due to a low VSWR and high gain
-
Suitable for broadband digital modulation thanks to a good VSWR flatness
-
Small, light-weight and flat antenna easy to use in narrow spaces
-
Easy handling with a flexible arm
-
A wide radiation pattern makes directivity of the fields no longer an issue
AMETEK Programmable Power
Located in San Diego, California, AMETEK Programmable Power designs, manufactures, and markets precision, AC and DC programmable power supplies, electronic loads, application specific power subsystems, and compliance test solutions for customers requiring and valuing differentiated power products and services. Also part of our business is VTI Instruments, which delivers precision modular instrumentation and systems for electronic signal distribution, acquisition, and monitoring, used in the world's most demanding test applications.
AMETEK Programmable Power boasts one of the industries' broadest portfolios of programmable power products under the well-known and respected Sorensen, Elgar, and California Instruments brands. AMETEK Programmable Power’s products serve a wide range of stimulus (T&M) and process power needs in applications including semiconductor fabrication, commercial and defense ATE, oil exploration, solar array and battery string simulation, avionics, general R&D and EMC compliance testing.
VTI Instruments provides products and systems which are used to monitor and record data that characterizes the physical integrity and performance of aircraft, engines, and other large structures, as well as automate the functional testing of complex electronic systems. VTI Instruments is recognized as an industry leader with a reputation of providing reliable data, first time, every time.
With strong brands, a broad product portfolio, exceptional precision power conversion and control expertise, proven power system integration capabilities and deep applications knowledge, AMETEK Programmable Power is your source for programmable power supplies, precision data acquisition instruments, and more.
Contact Details
AMETEK Programmable Power, Inc. − San Diego
9250 Brown Deer Road, San Diego, CA 92121, USA
Phone: 858-450-0085
Fax: 858-458-0267
Email: sales.ppd@ametek.com for general inquiries
Test & Measurement
Download Line Card
Document
