Teledyne LeCroy - ZD200 200 MHz, 3.5 pF, 1 MOhm Active Differential probe
With the ProBus interface, the ZD200 becomes an integral part of the oscilloscope. The probe sensitivity and offset are automatically optimized based on the oscilloscope gain settings, so control is transparent to the user. When used with a LeCroy digital oscilloscope, no external power supply is required.
The ZD200 probes provide a wide dynamic range of ±20 V and a common mode range of ±60 V to allow a broad application use.
Engineers often need to probe a variety of different test points in confined spaces. The extensive range of standard and optional tip accessories for the ZD200 Series of probes ensures that this probe can meet any difficult probing challenge. Innovative Probe Leads and Tips Provide Excellent
Probing with long leads or accessories is sometimes necessary to reach the test points, but it comes at the expense of reduced bandwidth, increased capacitance, and added noise. The ZD200 accessories are engineered to provide the best signal fidelity and minimize peaking and other undesirable effects often introduced with probe tips and leads.
Bandwidth (Warranted) 200MHz
RiseTime 10-90% (Typical) 1.75 ns
Probe Attenuation (Nominal) 10X
LF Attenuation Accuracy (Warranted) <2 mV
Probe Only Noise (Typical) 3 mVrms
Input Differential Range (Nominal) ±20V
Common Mode Range (Nominal) ±60V
CMRR (Typical)
- 80 dB @ 60 Hz
- 50 dB @ 10 MHz
DC Input Resistance
- 250 kΩ (Common Mode)
- 1 MΩ (Differential Mode)
Input Capacitance (Differential) (Typical) 3.5 pF
More Product Information
-
Provides a passive PCIe® backplane for test applications
-
Self-contained, portable and selfpowered
-
Supplies power for +3.3V, +3.3Vaux and +12V rails
-
Generates PCIe reference clock
-
Accepts external clock inputs
-
Generates valid PERST# bus reset that can be activated by manual push button
-
Includes two mid-bus probe footprints for traffic monitoring
-
Supports two PCIe x16 sockets which accept cards of any link width (x1, x4, x8, x16)
-
Provides indication of valid connection of PRSNT1# and PRSNT2# lines for each card
-
Supports data rates of 2.5 GT/s and 5.0 GT/s
-
Choice of 8, 10, or 13 GHz bandwidth models
-
3.5 Vpk-pk dynamic range
-
±4 V offset range
-
Ideal for DDR3, DDR4, LPDDR3
-
Deluxe soft carrying case
-
Wide variety of tips and leads
-
Solder-In Lead
-
Positioner (Browser) Tip
-
SMA/SMP Lead
-
Square Pin Lead
-
-
SMA/SMP lead set accessory does not require purchase of a different amplifier
-
Low loading and high imedance for minimal signal disturbance
The PPE series of probes are suitable for a wide range of applications where high-voltage measurements must be made safely and accurately. There are five fixed-attenuation probes covering a range from 2 kV to 20 kV, and one switchable probe providing ÷10/÷100 attenuation for voltage inputs up to 1.2 kV.
New technology which utilizes hybrid circuitry (and switch reading for probes with switchable gain/attenuation) minimizes ringing and overshoot to provide a precise response.
All fixed-attenuation, standard probes automatically re-scale any Teledyne LeCroy 9300C or LC series oscilloscope for the appropriate attenuation factor of the probe.
-
500 MHz - 4 GHz bandwidths
-
Up to 40 GS/s sample rate
-
15.4" capacitive touch screen
-
MAUI with OneTouch
-
Powerful, Deep Toolbox
-
Exceptional Serial Data Tools
-
16 digital channels with 1.25 GS/s
-
Huge Applied Offset Range
-
Optional Application Packages
With the ProBus interface, the ZD200 becomes an integral part of the oscilloscope. The probe sensitivity and offset are automatically optimized based on the oscilloscope gain settings, so control is transparent to the user. When used with a LeCroy digital oscilloscope, no external power supply is required.
The PPE series of probes are suitable for a wide range of applications where high-voltage measurements must be made safely and accurately. There are five fixed-attenuation probes covering a range from 2 kV to 20 kV, and one switchable probe providing ÷10/÷100 attenuation for voltage inputs up to 1.2 kV.
New technology which utilizes hybrid circuitry (and switch reading for probes with switchable gain/attenuation) minimizes ringing and overshoot to provide a precise response.
All fixed-attenuation, standard probes automatically re-scale any Teledyne LeCroy 9300C or LC series oscilloscope for the appropriate attenuation factor of the probe.
-
Allows TekProbe interface level II probes to work with any ProBus-equipped Teledyne LeCroy oscilloscope
-
Automatic probe detection
-
Provides all necessary power and offset control to the attached probe
-
Supports probes up to 4 GHz
-
Easy firmware updates
-
Wide variety of probes supported including:
-
Preamplifiers
-
Current Probes
-
Single-Ended Active Probes
-
Differential Active Probes
-
With the ProBus interface, the ZD500, 1000, and 1500 becomes an integral part of the oscilloscope. All probe gain and offset controls are transparent to the user, making it easier to probe the circuit without concern for which gain setting to choose. When used with a LeCroy digital oscilloscope, no external power supply is required.
Teledyne LeCroy
Teledyne LeCroy is a leading provider of oscilloscopes, protocol analyzers and related test and measurement solutions that enable companies across a wide range of industries to design and test electronic devices of all types. Since our founding in 1964, we have focused on creating products that improve productivity by helping engineers resolve design issues faster and more effectively.
Oscilloscopes are tools used by designers and engineers to measure and analyze complex electronic signals in order to develop high-performance systems and to validate electronic designs in order to improve time to market. Protocol analyzers are tools used by designers and engineers to generate and monitor traffic over high speed serial data interfaces, including DDR, PCI Express, Fibre Channel, Serial ATA, SAS, USB and others. Both products are critical in the development of a wide variety of demanding design applications.
We utilize both of these important product areas in combination to tackle the most demanding serial data test applications, offering tailored solutions to help our customers perfect their chips, interfaces, subsystems and products which utilize these important communications standards. With the explosion in the use of serial data communications technologies in semiconductors, between devices on circuit boards and between computers and peripherals, we are aimed at a growing and important market.
Our oscilloscopes offer a powerful combination of large and informative displays combined with advanced waveshape analysis capabilities typically tailored to enhance the productivity of engineers in specific applications areas such as serial data test, disk drive test and automotive bus analysis.
Headquartered in Chestnut Ridge, New York, LeCroy has sales, service and development subsidiaries in the US and throughout Europe and Asia. LeCroy products are employed across a wide variety of industries, including semiconductor, computer, consumer electronics, military/aerospace, automotive/industrial, and telecommunications.
Contact Details
Headquarters Teledyne LeCroy
700 Chestnut Ridge Road, Chestnut Ridge, NY 10977-6499, USA
Phone: 800-553-2769 or 845-425-2000
Phone Support: 1-800-553-2769
Fax Sales: 845-578-5985
Email Sales: contact.corp@teledynelecroy.com
Email Support: support@teledynelecroy.com (Oscilloscopes, Waveform Generators, Signal Integrity)