-
This ultra high intensity line light series is built to handle the most extreme line scan lighting requirements.
-
Provides an intensity level of 2,100 klx (working distance of 75 mm).
-
Pre-engineered for expandability in 150 mm (6”) increments up to 2400 mm (94.5”).
-
Available in multiple wavelengths.
-
In the event of abnormally high ambient temperatures, the device automatically shuts down when the housing reaches 60°C and resumes operation at 56°C.
-
Note: Requires third party power supplies – refer to spec sheet.
IntelliPower - FA10053 Power Distribution Unit
-
External Input/output panel with GFD, ISOMETER, and EPO
TYPE | SPECIFICATION |
---|---|
Power Rating | 150W |
Chassis Configuration | 6U, ≥24"D |
Input Voltage | 208 VAC |
Input Frequency | 50/60 |
Input Connector | Terminal Block |
Output Voltage | 110 VAC |
Output Frequency | 50/60 |
Output Connector | Terminal Block |
More Product Information
-
Accurate measurement of 121.5/243 MHz emergency beacon transmitter frequency, output power, modulation (AM). Headphone audio output to monitor swept tone *
-
Accurate measurement of 406 MHz COSPAS/SARSAT emergency beacon transmitter frequency, output power. Decode and display of all location and user protocols *
-
Accurate measurement of HF transmitter, frequency, output power, modulation (AM and SSB USB/LSB) receiver sensitivity
-
Accurate measurement of VHF/UHF transmitter, frequency, output power, modulation (AM and FM and receiver sensitivity)
-
Generation of ARINC 596 Selective Calling Tones
-
Accurate measurement of VHF/UHF antenna and or feeder SWR (Standing Wave Ratio)
-
Simulation of Localizer and Glideslope (CAT I, II and III) signals with variable DDM settings
-
Swept Localizer DDM for coupled Auto Pilot testing (Simultaneous Localizer, Glideslope and Marker signals)
-
Simulation of Marker Beacon, Selectable Airways (Z), Outer and Middle Marker Tones
-
Guided Test capability cuts down total test time
-
Low cost ELT option
-
Frequency counter provides external frequency measurement
-
MORSE CODE provides 1-4 characters transmitted in the VOR and ILS localizer mode
-
Eight or more hours of operation before recharge
-
Automatic power shut-down
-
Ergonomic design
-
8000VA, 6000W, 220VAC 50/60Hz Input and 220VAC 50/60Hz Auto Sensing Output, Double Conversion, On Line, High Temperature, Isolated, Rugged UPS with Power Factor Correction for Military Applications
-
External Battery Pack w/ 2 strings of 9 LiFe Batteries (14 Total) in 3U24” D Enclosure
-
6600VA, 5800W, 440 VAC 3Ph 60Hz Isolated Input, 220 VAC 1Ph 60Hz Output, Freq Changer, 4U26, L16 20P, L6 30R, SNMP, w/ Anderson EBP, Double Conversion, Rugged, High Temperature, On line UPS with Hot Swap Battery Drawer, and Power Factor Correction
-
3000VA, 3000W, 120/240VAC 50/60Hz Input and 120VAC 60Hz Output UPS
-
Double Conversion, Online, Free-Standing UPS System for Ground Applications
AR’s microwave amplifiers are just as tough and dependable as our RF amplifiers, and they are backed by the same comprehensive warranty. Our microwave amplifiers offer the hard-to-find combinations of power and bandwidth in frequency increments and power output you need for today’s test applications.
-
16 each 12V14Ah Pb-Acid batteries fixed within a 3U aluminum chassis
IntelliPower, Inc.
IntelliPower, Inc., located in Orange, California, has been designing, manufacturing and supporting high-performance, cost effective Uninterruptible Power Systems (UPS) and frequency/voltage conversion solutions to protect mission-critical applications since 1988. IntelliPower’s on-line, double conversion UPS, power conditioner and frequency/voltage converter solutions utilize digitally controlled, high-efficiency power switching technology that has been proven for over 32 years on numerous platforms.
Customers with demanding environments use IntelliPower’s rugged products because of our proven record of providing outstanding solutions. IntelliPower’s in-house development proprietary circuit design, DSP firmware/software technology and wide range of enclosure designs, give IntelliPower unmatched capabilities to deliver systems configured to customer requirements backed by expert support.
Our ability to design and configure quickly is based on our standard proprietary subassemblies that go into variations of our power systems as required. Our product configurator tools and application engineers allow you to easily define your requirements and obtain your proposal for solutions that exactly meet your needs.
Contact Details
IntelliPower, Incorporated
1746 North Saint Thomas Circle, Orange, California 92865, USA
Phone: 714-921-1580
Fax: 714-921-4023
Email: ca-ora-sales@ametek.com
Contact form