• Choice of 4 GHz or 6 GHz bandwidth models 
• Up to 5 Vpk-pk dynamic range with low noise 
• ±3 V offset range 
• Low loading and high impedance for minimal signal disturbance 
• Ideal for DDR2, DDR3, LPDDR2 
• Deluxe soft carrying case 
• Innovative QuickLink architecture 
• Wide variety of tips and leads 
  • Solder-In Lead 
  • Optional Positioner (Browser) Tip 
  • Quick Connect Lead 
  • Square Pin Lead 
  • HiTemp Solder-In Lead

• Highest resolution - 12 bits all the time 
• Bigger Display, smaller footprint, most bench space 
• More capability, increased productivity

• 2, 4 and 8 channel configurations 
• 16-bit vertical resolution 
• Sample Rate up to 12,32 GS/s with RF mode 
• 16-bit vertical resolution. 
• 4 GSample waveform memory per channel 
• Up to 5 Vpp Output Voltage and ±2.5 V Baseline Offset (into 50?)

• Available in 30MHz, 40MHz, 60MHz, 80MHz, 120MHz, 200MHz, 350MHz and 500MHz models
• All models feature 2 channels
• Max Sampling rate of 150 Msa/s (30MHz & 60 MHz) 1.2 Gsa/s (40MHz, 80MHz, 120MHz) and 2.4 Gsa/s (200MHz, 350MHz and 500MHz) models.
• Up to 16-bit vertical resolution (14-bit on 30MHz & 60MHz models).
• All models have 4.3" Touchscreens.
• Excellent analog and digital modulation types available (AM, DSB-AM, FM, PM, PSK, FSK, ASK and PWM)

• Vector Network Analyzer Frequency Range from 10 MHz up to 3.2 GHz 
• Spectrum Analyzer Frequency Range from 9 kHz up to 3.2 GHz 
• -156 dBm/Hz Displayed Average Noise Level (Typ.) 
• -98 dBc/Hz @10 kHz Offset Phase Noise (1 GHz, Typ.) 
• Total Amplitude Accuracy < 1.2 dB 
• 1 Hz Minimum Resolution Bandwidth (RBW) 
• All-Digital IF Technology 
• Standard Preamplifier 
• Distance to fault capability using VNA time domain analysis 
• Up to 1.5 GHz Tracking Generator Kit 
• Built-in Advanced Measurement capability (CHP, ACPR, OBW, CNR, TOI, etc) 
• 10.1 lnch WVGA (1024 x 600) Display

• S-parameters DC to 40 GHz, single-ended and mixed-mode 
• Impedance Profile with <1 mm resolution, differential and common-mode 
• Internal, automatic OSLT calibration 
• USB-connected, small, lightweight 
• Flexible display of the measurements 
• Remove effects from fixtures, connectors and cables 
• Emulate eye diagrams with CTLE, DFE and FFE equalization 
• Advanced jitter analysis

• High signal fidelity to 4 GHz bandwidth 
• Low circuit loading – High input impedance and low capacitance 
• 4 GHz, 2.5 GHz, 1.5 GHz and 1 GHz models 
• 1 MΩ input resistance 
• 0.6 pF (4 GHz) and 0.9 pF input capacitance 
• ± 8 V input dynamic range, ± 12 V offset range 
• Wide variety of tips and grounds 
• Easy to use, integrated with oscilloscope

Transmission line probes are a special type of passive probe designed for use at very high frequencies. They replace the high impedance probe cable found in a traditional passive probe with a precision transmission line, with a characteristic impedance that matches the oscilloscope input (50 Ohm). This greatly reduces the input capacitance to a fraction of a picofarad, minimizing the loading of high frequency signals. A matching network at the tip increases the DC input resistance. While they have lower DC input resistance than a traditional passive probe (usually 500 Ohm) to 1kOhm), the input impedance of these probes remains nearly constant over their entire frequency range. A traditional /10 passive probe will have a 10 MOhm) input impedance at DC, however this impedance drops rapidly with frequency, passing below the input impedance of a transmission line probe at less than 100 MHz.