Sorensen - DLM 600 1/2 Rack Programmable DC Power Supplies
- High Power Density: 600 watts in 1U (1.75 inches) high, half rack (8.5 inches) wide; no top or bottom clearance spacing required.
- Near Linear Ripple & Noise Ripple as low as 2.5mV rms, noise as low as 15mV p-p.
- Remote Control
- LXI Compliant Ethernet LAN / RS-232C (16 bit)
- IEEE-488.2 / RS-232C (12 bit)
- Standard analog programming 0-5V, 0-10V, or 0-5kΩ.
The Sorensen DLM 600 series of DC programmable power supplies are designed to provide continuously variable DC output voltage and current for a broad range of applications in a compact 1U (1.75 inches) high, half-rack (8.5 inches) wide chassis.
With the use of Zero Voltage Switching (ZVS) technology, these supplies can achieve exceptionally low ripple and noise rivaling larger and more expensive linear power supplies.
In addition, the high efficiency and fast load transient response assure that the DLM 600 1/2 rack DC power supply is ideal for even the most demanding applications.
The DLM 600 variable DC power supply series is ideal for high-density multiple output rackmount requirements or low-profile benchtop applications. Output voltages from 0-5VDC to 0-300VDC and currents from 0-2A to 0-75A are available.
The cooling air intake is at the front and sides with exhaust at the rear and sides. Variable speed fans are controlled as a function of ambient air temperature and load, thus reducing acoustic noise, and increasing fan life. This allows programmable DC supplies to be stacked one directly on top of another without space in between, yielding maximum rackmount packing density and a wide operating temperature of 0-50° C. An optional rackmount kit is available to easily mount one- or two units side-by-side.
The front panel layout makes the DLM 600 DC power supply series easy to use. Voltage and current can be set from individual 10-turn potentiometer knobs. Control push buttons include power on, output on, local/remote, voltage/current preview, and overvoltage protection preview. Set point or actual voltage/ current values can be viewed on two 3-1/2-digit LED displays.
DLM 600 near-linear DC power supplies can be connected in series or parallel. All models automatically accept any standard single-phase input without manual setup.
Features and Benefits
High Power Density
600 watts in 1U (1.75 inches) high, half rack (8.5 inches) wide; no top or bottom clearance spacing required.
Near Linear Ripple & Noise
Ripple as low as 2.5mVrms, noise as low as 15mV p-p.
Remote Control
- 16-bit programming through LXI-compliant Ethernet LAN / RS-232C (Option M130)
- 12-bit programming through IEEE-488.2 / RS-232C (Option M9G)
- Standard analog programming 0-5V, 0-10V, or 0-5kΩ.
- isolated analog programming (option)
Pushbutton Preview
Overvoltage protection, voltage, and current preview buttons allow viewing these set points at any time with or without the output enabled.
Active Down Programming
Standard internal circuitry to speed up response time to down programming changes.
Universal AC Input
Easy leader/follower paralleling with active current sharing.
Software
- IVI-com driver for M130 option
- Labwindows CVI driver for M9G option
- Labview driver for M9G option
5 Year Warranty
|
Model |
DLM 600 |
|---|---|
|
Voltage |
5V - 300V |
|
Current |
2A - 75A |
|
Power |
375W - 600W |
|
Overview |
1/2 Rack Programmable DC Power Supplies |
More Product Information
The SMP6xxx product family is made up of the SMP6001, SMP6002, SMP6004, SMP6005, SMP6006, SMP6101, SMP6102, SMP6103, SMP6122, SMP6144, SMP6202, SMP6301 (pictured), SMP6301T, and SM6306.
- Highest Power Density
- Comprehensive Digital and Analog Interface Options
- Scalable, Multi-Unit Design
- Multi-Channel Support
- Straightforward Front Panel Controls
- High Reliability
- High Power Density: 600 watts in 1U (1.75 inches) high, half rack (8.5 inches) wide; no top or bottom clearance spacing required.
- Near Linear Ripple & Noise Ripple as low as 2.5mV rms, noise as low as 15mV p-p.
- Remote Control
- LXI Compliant Ethernet LAN / RS-232C (16 bit)
- IEEE-488.2 / RS-232C (12 bit)
- Standard analog programming 0-5V, 0-10V, or 0-5kΩ.
FormFactor - Cascade Ultra High-Power (UHP) - Enabling single-contact high-current/high-voltage test
-
Enables coaxial measurements up to 10,000 V and 300 A pulsed (600 A in a parallel configuration) with a single touchdown
-
Even distribution of high current with innovative multi-fingertip design
-
Compatible with TESLA 200/300 mm power device characterization system
-
Reduced measurement time by testing both high-voltage and high-current conditions with a single touchdown
-
Accurate characterization of a wide range of pad sizes and test currents, with minimum pad damage and contact resistance
-
Safe, reliable and repeatable high-current/voltage measurements over a wide temperature range (from -55°C to +300°C)
- Three independent, isolated 1700W DC outputs, 5100W total
- 1U rack-mount chassis
- 9 output options
- Multi-language, intuitive, color touch panel control
- Global 3-Phase AC Input options for system phase balancing
- Active power factor correction (PFC)
- Multi-channel programmable sequencing, ramps, and delays
- Full remote control via Virtual Panels™ GUI
- Standard LXI Ethernet, USB, and RS232 control interfaces
- Optional GPIB control interface or isolated analog programming
- Multiple voltage⁄current ranges
- Direct numeric entry and incremental rotary control of voltage and current
- The remote or local sense
- Illuminated keys and display legends.
- Up to ten store/recall set-ups (30 setups for triple output)
- Power output display
- Link and copy mode
-
On-wafer power device characterization up to 10,000 V DC / 600 A
-
Safe and convenient integration kits to support T.I.P.S. “LuPo” High Voltage / High Power Probe Cards
-
Prevent thin wafers from curling and breaking
-
Safety interlock system with clear enclosure for operator safety during device measurements
-
Convenient connection kits for easy and safe system integration with power device analyzers from Keysight Technologies and major suppliers
-
Up to 25% lower air consumption (CDA) than other systems in the market (300l/min) with no compromise in transition times
-
Windows 10 compatibility enables highest performance and safe operation with state-of-the-art hardware
See more Key Features on Specifications & Details tab
-
Versatile temperature range for extreme environments
-
IEEE 1588 PTP
-
Power over Ethernet
-
P-Iris and DC-Iris lens control
-
Monochrome (GT1600) and color (GT1600C) models
-
GigE Vision interface with Power over Ethernet
-
Screw mount RJ45 Ethernet connector for secure operation in industrial environments
-
Supports cable lengths up to 100 meters (CAT-6 recommended)
-
Trigger over Ethernet Action Commands allow for a single cable solution to reduce system costs
-
Comprehensive I/O functionality for simplified system integration
-
Popular C-Mount lens mount
-
Easy camera mounting via standard M3 threads or optional tripod adapter
-
Easy software integration with Allied Vision's Vimba Suite and compatibility to the most popular third party image-processing libraries.
- Analog Programming
- Constant Voltage or Constant Current Operation
- LabView® and LabWindows® Drivers
- Standby Mode
- Front Panel Button Preview of Voltage, Current, OVP
- CSA, UL Approvals
AMETEK Programmable Power
Located in San Diego, California, AMETEK Programmable Power designs, manufactures, and markets precision, AC and DC programmable power supplies, electronic loads, application specific power subsystems, and compliance test solutions for customers requiring and valuing differentiated power products and services. Also part of our business is VTI Instruments, which delivers precision modular instrumentation and systems for electronic signal distribution, acquisition, and monitoring, used in the world's most demanding test applications.
AMETEK Programmable Power boasts one of the industries' broadest portfolios of programmable power products under the well-known and respected Sorensen, Elgar, and California Instruments brands. AMETEK Programmable Power’s products serve a wide range of stimulus (T&M) and process power needs in applications including semiconductor fabrication, commercial and defense ATE, oil exploration, solar array and battery string simulation, avionics, general R&D and EMC compliance testing.
VTI Instruments provides products and systems which are used to monitor and record data that characterizes the physical integrity and performance of aircraft, engines, and other large structures, as well as automate the functional testing of complex electronic systems. VTI Instruments is recognized as an industry leader with a reputation of providing reliable data, first time, every time.
With strong brands, a broad product portfolio, exceptional precision power conversion and control expertise, proven power system integration capabilities and deep applications knowledge, AMETEK Programmable Power is your source for programmable power supplies, precision data acquisition instruments, and more.
Contact Details
AMETEK Programmable Power, Inc. − San Diego
9250 Brown Deer Road, San Diego, CA 92121, USA
Phone: 858-450-0085
Fax: 858-458-0267
Email: sales.ppd@ametek.com for general inquiries
Test & Measurement
Download Line Card
Document
