• IEC 61000-4-4 Ed.3 standard compliance. 
• Pre-check function is installed. Inspection before testing is now easy. 
• Normal mode test support. Taking account of field troubles is possible. (option) 
• Utilize an outlet box that simplifies EUT connection. (option) 
• Compared with conventional products, the size has become compact. (Approximately 67% by volume) 
• Easy to understand Panel display reduces mistakes in connecting power cables. 
• Software control with Windows. (option) 
• Next calibration date can be notified. (Windows software only) 
• Employ LCD screen with multi-language support and enhanced operability. 
• Maximum output voltage of 5 kV and maximum pulse frequency of 2 MHz allow you to test above the standard test level. 
• CDN capacity is increased to single phase type AC 240 V 20 A, single and three phase type to AC 600 V 63 A, supporting wider range of EUT. 
• Large capacity CDN (100 A or 150 A) option available for Injection test on various EUT. 
• Using coupling clamps, EMS probe kits, you can test the signal lines and evaluate the noise immunity on the PCB. (option)

• Calibration-grade metrology standards
• Used for VNA calibration and/or calibration validation

Shielded, coaxial opens are used in the calibration of vector network analyzers to provide a nominal 180° phase offset from a compatible reference short over a wide range of frequencies. At these frequencies, open circuit terminations are inherently imperfect. Shielding the open essentially eliminates radiation loss, but creates a residual frequency-sensitive capacitance. An accurate knowledge of the open’s effective capacitance is essential to an accurate calibration of the analyzer. Maury opens are characterized for effective capacitance versus frequency by means of a fourth order polynomial curve fit, and the nominal capacitance coefficients are provided with each unit.

• Calibration-grade metrology standards
• Used for VNA calibration and/or calibration validation

A precision fixed termination (or load) consists of an immovable, (fixed) termination which, when mated to the end of a trans-mission line or cable, absorbs nearly all of the signal energy traveling toward it. An ideal “matched” condition exists when a termination with an impedance value of Z0, is connected to the end of a transmission line or cable that also has a characteristic impedance of Z0. Such an ideal “matched” condition (one with no mismatch between the termination and its mated line or cable) is critical if a voltage standing wave ratio (VSWR) of 1.0:1 is to be achieved in a system with a 50 or 75 ohm impedance value. Simply put, the more closely the 1.0:1 ratio is approached, the more accurate the measurements that can be made from a system.

• Vector Network Analyzer Frequency Range from 10 MHz up to 3.2 GHz
• Spectrum Analyzer Frequency Range from 9 kHz up to 3.2 GHz
• -156 dBm/Hz Displayed Average Noise Level (Typ.)
• -98 dBc/Hz @10 kHz Offset Phase Noise (1 GHz, Typ.)
• Total Amplitude Accuracy < 1.2 dB
• 1 Hz Minimum Resolution Bandwidth (RBW)
• All-Digital IF Technology
• Standard Preamplifier
• Distance to fault capability using VNA time domain analysis
• Up to 1.5 GHz Tracking Generator Kit
• Built-in Advanced Measurement capability (CHP, ACPR, OBW, CNR, TOI, etc)
• 10.1 lnch WVGA (1024 x 600) Display

• S-parameters DC to 40 GHz, single-ended and mixed-mode
• Impedance Profile with <1 mm resolution, differential and common-mode 
• Internal, automatic OSLT calibration
• USB-connected, small, lightweight
• Flexible display of the measurements
• Remove effects from fixtures, connectors and cables
• Emulate eye diagrams with CTLE, DFE and FFE equalization
• Advanced jitter analysis

• Broadband coverage
• Extremely good temperature stability
• Superior voltage stability
• Noise figure meter-compatible

The NC346 Series is designed for precision noise figure measurement applications. Each module’s low VSWR reduces multiple reflections and significantly increases the measurement accuracy for most noise figure test configurations.

20 ppm calibrator of DC process signals designed for calibration of evaluation units and process multimeters under demanding industrial conditions. 

• 20 ppm accuracy
• 13°C - 33°C reference temp. range
• 100 V @ 25 mA output capacity

High resistance decade with built-in test signal meter for calibration of high resistance meters up to 6 kV. Based on M6xx Real-Resistance decade series with short function for short current testing.

• 10 kΩ - 100.0 GΩ, short function
• Hot-switching up to 6 kVdc limit
• Test voltage and current indication

• Calibration-grade metrology standards
• Used for VNA calibration and/or calibration validation

Fixed flush and fixed offset short circuit terminations (shorts) are used to establish reference planes in transmission systems and as key elements in the calibration of vector network analyzers (VNAs). Offset shorts can be used for banded calibrations of VNA. Those with the longest offset are often used to evaluate the calibration effectiveness of a VNA by measuring the effective source match after calibration.