• With an intensity of over 150 klx at 300 mm WD in continuous operation, the SL316 UltraSeal Spot Light delivers industry-leading intensity with consistent uniformity. 
• Available with narrow, medium, and wide lensing options as well as a non-lensed configuration for high dispersion. 
• Configurable in eleven wavelength options. 
• Compatible with all Ai inline and discreet control systems. The SL316 can be operated in continuous, gated continuous, pulsed, and adaptive pulsed modes with dimming options for brightness control.

• Ideal for applications requiring high ENR and immunity to large incident RF power
• Low VSWR
• Built-in isolator

The NC3400 Series coaxial AWGN noise sources are an excellent choice for applications requiring high ENR and immunity to large incident RF power, such as ATE, radiometer, and radar systems. The calibration accuracy and flatness of the NC3400 Series noise sources are enhanced by their low VSWR. The built-in isolator provides almost constant output impedance as the noise source bias is switched on and off. The isolator also protects the noise diode from incident RF power (consult the factory for higherpower units).

An SMA female connector is standard for the RF output and a BNC female connector is standard for the bias input. Other connectors are available as options.

Environmental Control

• Wafer temp verified <4.5 K (with 44 RF probes in contact) 
• Magnetic field suppression to <200 nT​
• Highly uniform wafer temperature
• Precise thermal stability and control
• Solid construction with granite base enables precision motion and vibration control

See "Specifications & Details" tab for more key features

• Directly compatible with most commercial VNA’s
• Available as polynomial and characterized device kits
• Measure S-Parameters with uncertainty when used in conjunction with Maury’s Insight software platform

Maury offers coaxial and waveguide VNA calibration kits.

Coaxial calibration kits are offered in Polynomial SOLT, Characterized Device (CD) SOLT, and TRL, depending on the connector series. Where available, CD kits improve calibration accuracy when compared to SOLT kits based on polynomial definitions as each calibration kit is provided with individually characterized short, open and fixed load standards, whose S-parameters can be loaded into commercial VNAs directly or when used with Maury’s Insight™ software platform. When combined with Insight™, users will be able to quantify the uncertainty contribution of their calibration kit to their overall measurements. CD cal kits result in TRL-like accuracy with fixed-load SOLT ease-of-use.

The overall performance of a power meter dependents on the power sensor employed. Maury has a variety of quality power sensors to meet virtually all applications. Maury has a complete line of Peak and Average power sensors up to 40 GHz for all of your fast rise time, wide bandwidth and wide dynamic range applications. In this document, browse through our large variety of advanced sensor solutions.

• Calibration-grade metrology standards
• Used for VNA calibration and/or calibration validation

A precision fixed termination (or load) consists of an immovable, (fixed) termination which, when mated to the end of a trans-mission line or cable, absorbs nearly all of the signal energy traveling toward it. An ideal “matched” condition exists when a termination with an impedance value of Z0, is connected to the end of a transmission line or cable that also has a characteristic impedance of Z0. Such an ideal “matched” condition (one with no mismatch between the termination and its mated line or cable) is critical if a voltage standing wave ratio (VSWR) of 1.0:1 is to be achieved in a system with a 50 or 75 ohm impedance value. Simply put, the more closely the 1.0:1 ratio is approached, the more accurate the measurements that can be made from a system.

• 4 kHz to 6 GHz and 10 MHz to 6, 18, and 40 GHz power sensors
• -60 dBm to +20 dBm dynamic range
• Pulse, Average, CW and Modulation modes
  • True average measurements with essentially no modulation bandwidth limitations
• Real-Time Power Processing™ technology for virtually no gaps in signal acquisition and zero measurement latency
• 100,000 measurements per second
• Synchronized multi-channel measurements
• Suite of advanced measurement and analysis software

• S-parameters comparison of user-characterized and factory-characterized verification standards
• S-parameters comparison of user-characterized and factory-characterized verification standards with measurement uncertainty boundaries
• Includes beaded airline, mismatch airline, offset shorts and fixed loads

• Dual-channel and differential voltage measurements
• 1% accuracy at full scale
• True RMS response below 30 mV
• Optional low-frequency probe for measurements from 10 Hz to 100 MHz
• DC recorder output
• IEEE-488 interface standard, RS-232

The 9240 series is the latest addition to the popular 9200 series of RF voltmeters. It combines accuracy, smart probes, and operator features that have never before been available in its price range. It is simple to use on the bench, and comprehensive enough to integrate into an ATE system. Boonton’s proven voltage probes directly measure from 200 μV to 10 V with usable indication as low as 50 μV and have true RMS response below 30 mV.