• Object size / measuring range up to 130 mm (5.11“) (larger customizations are possible) 
• Quick and very easy measurement 
• Little training required (without a customer specified database an initial operating instruction takes only 15 min) 
• Suitable software: VELOX (measuring software), ProCable3 (CAQ system) 
• Various external CAQ software are connectable (CIQ-AESA, ADVARIS, QDA-ASI-DATAMYTE, QUASAR, etc.) 
• No user influence on default optical focus as well as default optimized, intelligent and homogeneous lighting 
• Shock and vibration resistant due to an optimized sensor arrangement and balanced weight distribution 
• Quick and very precise measurements due to the robust construction and easy operation 
• Measuring software enables various operator level settings (production, laboratory, administrator, service, etc.) 
• Standardized individual components lead to supply security and therefore a short delivery period 
• Easy connection with external devices

• Eight ports of 8 I/O bits each 
• High current capability for control of external relays, 300 mA sink 
• Simulate and receive digital data at up to 2 MHz sample rates 
• Selectable output voltages range from 3.3 V to 60 V 
• Setup outputs and scan inputs as part of EX1200 measurement sequencing engine

• Cutting block SB 18 - The cutting base can be rotated 4 times and is exchangeable always an optimal cutting base
• Cutting knife - With special blades for an optimal cutting of the cable samples
• Special blades - These blades are especially developed for cable preparation
• Cable strippers - Different sizes

• Typical accuracies of ±0.20°C 
• 16-channel isolated universal thermocouple/voltage inputs 
• Power over Ethernet+ (PoE+) 
• 20K samples/second/channel sample rate 
• 24-bit ADC per channel 
• 500 V channel-ground isolation 
• 1000 V channel-channel isolation 
• Data logger acquisition mode 
• Built-in parallel data streaming 
• Full-featured embedded web interface 
• LXI Ethernet interface 
• 8-bit bank isolated digital I/O 
• Compact 1U half-rack form factor

• Measuring device to detect the twist/lay/pitch length of sheathed cables
• Measurements according to the standards LV212 und LV122
• The twist length of the sample is measured without removing the sheath → this ensures a precise measurement
• Traditional methods manipulate the sample (cable stripping or unwinding of conductors) → a precise measurement is not possible anymore
• Via a PC connection, the measuring results can directly be exported
• Fully automatic: By clicking one button, the measuring sensor automatically moves along the sample

• Up to 65 GHz 
• Up to 80 Channels @ 36 GHz 
• Up to 160 GS/s 
• Up to 512 Mpts/Ch 
• 50 fs rms Sample Clock (Intrinsic) Jitter 
• Jitter Between All Channels of <130 fs rms

All-in-One BERT and Sampling Oscilloscope

• Customized built-in 4ch sampling oscilloscope and 4ch BERT
• Fast measurement and high performance shorten test times, improve yields, and cut capital infrastructure costs
  • Sampling Oscilloscope
    • Fast: 250 ksamples/s to measure 1 Msamples in about 5 s
    • High Sensitivity: –15 dBm (typ., SMF)
    • Wide bandwidth: 35 GHz (optical, SMF), 25 GHz (optical, MMF), 40 GHz (electrical)
    • Low Jitter: 200 fs rms (typ.)
    • Both NRZ and PAM4 signal analysis, Supports 53-Gbaud analysis with PAM4
    • Built-in 26/53 Gbaud Clock Recovery Unit (CRU) for both NRZ and PAM4
    • NRZ Jitter component analysis
  • BERT
    • Low-Jitter PPG: 600 fs rms (typ.)
    • High-sensitivity ED: 25 mV (typ.)
• Built-in PC for stable fast performance

• 2, 4 and 8 channel configurations
• 16-bit vertical resolution
• Sample Rate up to 12.32 GS/s with RF mode
• 16-bit vertical resolution.
• 4 Gpts waveform memory per channel
• Up to 5 Vpp Output Voltage and ±2.5 V Baseline Offset 50 Ohm

• Measuring device for large extrusion tools up to 35 mm (1.37“) hole diameter 
• Automated measurement process 
• Focus indicator allows you to easily adjust the focus 
• Homogeneous transmitted light illumination - made by iiM GmbH - for the ideal presentation of the area to measured 
• The influence of the user is reduced to a minimum 
• Robust, ergonomic design 
• Ideal addition to the 2-camera system VCPEx+