• High speed up to 100 kHzx3 line rate (Mono) or 300 kHz line rate (Color)
• RGB native colors (Color)
• Independent exposure control (Color)
• Subpixel spatial correction (Color)
• Sequential exposure control (Mono)
• High dynamic range (Mono)
• Up to 100 m optical cable length

• Support the most high-performance Camera Link cameras with available support for Full and 80-bit mode at up to 85 MHz 
• Perform deterministic image acquisition by way of the jitter-free Camera Link 2.1 interface 
• Offload host computer of custom image processing using a field-programmable gate array (FPGA) device 
• Eliminate missed frames through a PCIe® 2.0 x8 host interface and ample onboard buffering 
• Optimize multi-camera applications via support for up to four Base or two Full/80-bit Camera Link cameras per board 
• Minimize space requirements and maximize PC compatibility through a half-length design with mini Camera Link connectivity for true single-slot operation
• Improve and simplify system connectivity with Power-overCamera-Link (PoCL) support at extended cable lengths

• True Differential and Calibrated TDR for Maximum Impedance Measurement Accuracy 
• Compact, Battery-Powered Design for true portability 
• 30 ps Typical Rise Time, S-Parameter support up to 15 GHz (15D and 15D-XR models) 
• 260 ps Typical Rise Time, S-Parameter support up to 1.25 GHz (01D model) 
• 50,000-point memory supporting DUT lengths up to 30 m (15D), 50 m (15D-XR) and 1 km (01D) 
• Automatic Ohmic Loss Compensation for enhanced accuracy 
• Built-in Skew Analysis (Inter-Pair and Intra-Pair) for differential signal integrity 
• XR Series: Engineered for Speed, Optimized for Continuous Cable Production 
• 01D model: Engineered for High-Dynamic Range, Optimized for 10Base-T1, 100Base-T1 and MIL-Spec RF Cables.

• Calibration-grade metrology standards
• Used for VNA calibration and/or calibration validation

A precision fixed termination (or load) consists of an immovable, (fixed) termination which, when mated to the end of a trans-mission line or cable, absorbs nearly all of the signal energy traveling toward it. An ideal “matched” condition exists when a termination with an impedance value of Z0, is connected to the end of a transmission line or cable that also has a characteristic impedance of Z0. Such an ideal “matched” condition (one with no mismatch between the termination and its mated line or cable) is critical if a voltage standing wave ratio (VSWR) of 1.0:1 is to be achieved in a system with a 50 or 75 ohm impedance value. Simply put, the more closely the 1.0:1 ratio is approached, the more accurate the measurements that can be made from a system.

• Uses standard PC Ethernet port & hardware 
• Supports cable lengths up to 100 m (CAT-5e or CAT-6) 
• Simplified set-up with field proven Sapera LT software featuring CamExpert 
• Engineered to accommodate industrial environment with a ruggedized screw mount RJ-45 connector

• For D415, D435, D455
• Robust construction
• High IP protection class
• High chemical resistance
• Vibration‐proof mounting
• Camera mount included
• Good heat dissipation
• Compact size
• Affordable price
• Adaptable to all Mounting Kits
• USB cable feeds through the cable gland

• Easy separation of cable jackets from the electrical conductor
• Suitable for samples with a high strip force
• Also designed for larger sample outer diameters (depending on wall thickness)
• Suitable preparation before cutting cable samples for measuring (e.g. with the ORC-series)
• Robust, stable construction
• Easy to use

• Excellent cutting results through precision cutting
• Improved sample quality through an exact and reproducible sample thickness
• Very durable blade, 7 times blade rotation possible (360°)
• Exact adjustment of the rotating speed
• The influence of the operator is minimized by the predefined blade feed
• Fine, manual dosing of the progressive feed
• Easy exchange of the wire grips possible, with standard tooling
• Intelligent control electronics ensure an intuitive and safe operation

Quantity in Stock: 1