AMETEK - Water Cooled Laser Power Current Source
-
Air to water heat exchanger added to system
-
True current source
-
Fast transient response
-
Little to no current overshoot
-
Low stored energy
Industry : science
Application : High Energy
Function : Provides main power directly to the laser diode stacks.
More Product Information
-
High Power AC and DC Power Source
-
Programmable AC and DC power for frequency conversion and product test applications
-
-
Expandable Power Levels
-
Available output power of 15, 22.5, 30, and 45 kVA per unit and multi-unit configurations for power requirements up to 135 kVA and above
-
-
Single and Three Phase Mode
-
Phase mode programming on MX22.5-3Pi, MX30-3Pi and MX45-3Pi allows switching between single and three phase output modes
-
-
Arbitrary & Harmonic Waveform Generation
-
User defined voltage waveform and distortion programming
-
-
Regenerative, bidirectional “Green” Power Solution
-
Automatic crossover between Source and Sink power mode offers regenerative capabilities in AC mode. Regenerate up to 100% of the rated output power back to the utility grid during sink mode operation. ( -SNK option )
-
-
Remote Control
-
Standard RS232C & USB along with optional IEEE- 488 & LAN Interfaces are available for automated test applications
-
-
High Power Density (2 VA/cubic inch)
-
Single or multi-phase output
-
Parallel operation
-
4.8 Crest factor
-
Digital control loop technology
-
≥0.95 PFC
-
Brown-out simulation
-
AC 875 VA
-
45 to 5000 Hz
-
Universal AC/DC input via mainframe
-
User configurable
-
Simple integration
-
Near Linear Power Supply
-
Modular
-
≥0.95 PFC
-
Digital control loop technology
-
High Power Density (3.5 watts/cubic inch)
-
“Virtual Assets” by:
-
Series operation
-
Parallel operation
-
Combined operation with loads
-
-
Simple integration
-
Total power subsystem integration
-
Power sequencing
-
Elapsed time indication
-
EMO function
-
Custom rear output panel
-
High Voltage (500V) Input
-
Digital control loop technology
-
Two models: 375W & 750W
-
Up to 750W/500V
-
Parallel up to 8 automatically
-
Modular
-
High Power Density
-
Simple integration
-
Ruggedized
-
Wide (Global) Input
-
On-Line Battery Back-Up
-
Transient (Spike) Suppression
-
Surge Suppression
-
Input Distortion Elimination
-
Direct PC bus access data acquisition system provides the required sampling rate and resolution to meet IEC 61000-4-7 measurement requirements and supports high speed data transfers, unlike competing IEC test systems which provide only limited throughput using IEEE-488.
-
PC based Harmonic and Flicker test software provides real-time full color data display updates and continuous PASS/FAIL monitoring.
-
Automatic calculation of the maximum permissible system impedance Zsys, using the Zref and measured Flicker parameters, as required per EN/IEC 61000-3-11.
-
Simple user operation under Windows provides IEC test setup, data analysis, display and MS Word test reports.
-
High resolution, no gap acquisition data storage to ensure that all data can be streamed to disk (in ASCII format if needed) for later review and replay of actual test.
-
Single Step and Fast playback mode of test results
-
Broadest Model Selection: 800W to 7.5kW (higher power available up to 250kW Contact Factory)
-
Exclusive Voltage Models: 60V to 1000V
-
Multiple loads in one: Multiple ranges for voltage, current resistance and power
-
Intuitive Front Panel Control: Run sequences, triggers, constant current to constant power cross over
-
RoHS Compliant
-
High Power Density: up to 15 kW in 3U, 30 kW in a 6U chassis
-
Wide Voltage Range: 0-10V up to 0-1000V, from 4 to 30 kW
-
Fast Load Transient Response: Protection from undesired voltage excursions
-
Low Ripple and Noise
-
Hardware Trigger (Ethernet Option)
-
Parallelable up to 150 kW
-
Sequencing: Free system controller & speed up test
-
Low audible noise: Temperature controlled variable speed fans
AMETEK Programmable Power
Located in San Diego, California, AMETEK Programmable Power designs, manufactures, and markets precision, AC and DC programmable power supplies, electronic loads, application specific power subsystems, and compliance test solutions for customers requiring and valuing differentiated power products and services. Also part of our business is VTI Instruments, which delivers precision modular instrumentation and systems for electronic signal distribution, acquisition, and monitoring, used in the world's most demanding test applications.
AMETEK Programmable Power boasts one of the industries' broadest portfolios of programmable power products under the well-known and respected Sorensen, Elgar, and California Instruments brands. AMETEK Programmable Power’s products serve a wide range of stimulus (T&M) and process power needs in applications including semiconductor fabrication, commercial and defense ATE, oil exploration, solar array and battery string simulation, avionics, general R&D and EMC compliance testing.
VTI Instruments provides products and systems which are used to monitor and record data that characterizes the physical integrity and performance of aircraft, engines, and other large structures, as well as automate the functional testing of complex electronic systems. VTI Instruments is recognized as an industry leader with a reputation of providing reliable data, first time, every time.
With strong brands, a broad product portfolio, exceptional precision power conversion and control expertise, proven power system integration capabilities and deep applications knowledge, AMETEK Programmable Power is your source for programmable power supplies, precision data acquisition instruments, and more.
Contact Details
AMETEK Programmable Power, Inc. − San Diego
9250 Brown Deer Road, San Diego, CA 92121, USA
Phone: 858-450-0085
Fax: 858-458-0267
Email: sales.ppd@ametek.com for general inquiries