LUMIMAX® High Power LED Spot Lights are particularly compact, but at the same time extremely powerful and versatile. 

Adjustable precision optics of the LED Spot Lights allow adjustment of the radiation characteristic to the required working distances and image fields, enabling a focused or very homogeneous illumination of the object to be inspected.

LED Spot Light's filter thread allows mounting of components such as polarisation filters or bandpass filters for fluorescence applications. With the C-Mount connector, either integrated or available as an accessory, lenses for focusing can be used.

Despite their compact design, the LUMIMAX® LED Spot Lights feature an integrated lighting controller for continuous or strobe mode.

• Uses standard PC Ethernet port & hardware 
• Supports cable lengths up to 100 m (CAT-5e or CAT-6) 
• Simplified set-up with field proven Sapera LT software featuring CamExpert 
• Engineered to accommodate industrial environment with a ruggedized screw mount RJ-45 connector

• The RL127 is characterized as a Large High Dispersion Bright Field ring light. 
• Non-lensed LEDs disperse light at broad angles, providing “soft” lighting for applications that require short to medium working distances. 
• The low-profile design is only .75” (19mm) thick, with an O.D. of 4.6” (117mm) and I.D. of 2.61” (66.3mm) allowing it to be used in space constrained applications. 
• The I.D. provides a standard 67mm diameter thread with a pitch of .75mm for further mounting flexibility. 
• A wide variety of wavelengths are available from UV to IR. An optional polarizer and/or diffuser may be used to further condition the light output. 
• The RL121 delivers 20kLux at a working distance of 100mm.

Southwest Microwave offers an array of field replaceable cable connectors, direct solder cable connectors and direct solder flange mount cable terminations. Contact us for high-performance .047, .086 and .141 flex cable assemblies or harnesses up to 110 GHz, delivering the industry’s lowest VSWR and insertion loss.

• Multi Tester with 16AMP CDN
• EFT/Burst 5kV IEC 61000-4-4
• Surge, Combination Wave 7kV IEC 61000-4-5
• Surge Magnetic field IEC 61000-4-9 (MSURGE-A loop antenna required)
• Ring Wave, 7kV IEC 61000-4-12 & ANSI
• Telicomm Wave, 7kV IEC 61000-4-5 & ITU
• AC Dips/Drops IEC 61000-4-11 (DIP 116 dips transformer required)
• DC Dips/Drops IEC 61000-4-29 (2x DC supplies required)

LSS-EF01 series

This simulator evaluates the immunity of electronic equipment by simulating "highenergy induced lightning noise" induced in power distribution lines and communication lines due to fluctuations in the earth's potential caused by lightning strikes. This is an entry model of the LSS-F03 series. (Maximum output voltage 6kV)

LSS-F03 series

A tester simulatively generates "High energy induced lightning noise" which induced to distribution lines or communication lines by ground potential fluctuation caused by lightning strikes.

• 9 kHz to 9/14/20/26.5/32/43.5/54 GHz
• DANL: -164 dBm (with preamp)
• TOI: +20 dBm (typical) Analysis bandwidth: 150 MHz
• Amp range: DANL to +30 dBm
• Phase noise at 1 GHz: -110 dBc/Hz @ 100 kHz offset (typical)
• Demodulation: 5GNR, LTE FDD/TDD, RF, and modulation quality plus SSB signal analysis
• Resolution bandwidth (RBW): 1 Hz to 10 MHz
• Sweep Speed: 40 GHz/second (full span)
• RTSA bandwidth: 22, 55, 120, 150 MHz (option dependent)
• Amplitude accuracy: < 14 GHz ± 1.3 dB (± 0.5 dB, typical)
• Zero span with 60 ns minimum span
• IQ capture and streaming
• AM/FM modulation quality measurements
• Built-in PDF/HTML report generation
• EMF Measurements
• Uplink/Downlink interference analysis
• Interference hunting
• Channel Scanner
• Coverage Mapping

• Image circle: 43.2 mm - 82 mm
• 4 focal lengths: 40 mm - 100 mm
• Homogeneous imaging performance across the entire image field
• Very low distortion and high resolution
• V38-Mount, compatible to theV38 mounting system
• Initial apertures: F2.8 - F5.6

EMC test equipment to evaluate the resistibility of electronic devices and components when energy charged on a human body or object is discharged to the electronic devices and components. NoiseKen brand ESD simulator is available to see malfunctions or function declines of electronic equipment for appropriate evaluations compliant with IEC 61000-4-2 Ed.2 Test Standard, ISO 10605 Ed.2 Test Standard & ISO 10605 Ed.3 Test Standard. 

The ESS-S3011A features a function which enables the user to pre-program test settings to minimize setup errors as well as having the unit be incorporated into a remote or autonomous testing setup. Another feature that sets apart NoiseKen ESD guns to that of competitors is the discharging gun separation design which helps achieve the lightweight. 

For conventional ESD guns, that have generators that are inseparable from the gun, you may experience having to replace the whole unit even only when certain parts of the unit are broken. However, with the NoiseKen’s separation design, replacement parts can be minimized to lower the running cost.