Fully Integrated: With the ProBus™ interface, the AP033 becomes an integral part of the oscilloscope. The probe sensitivity and offset can be controlled from the oscilloscope front panel, the probe front panel, or by using remote control commands (GPIB or RS-232). Sensitivity, offset, input capacitance, and common mode voltage range are displayed on the oscilloscope screen. When used with a LeCroy digital oscilloscope, no external power supply is required.

• Battery or rechargeable battery operation with polarity protection
• On/off switch
• Exactly calibrated red line
• 5mW output power
• Strong magnetic mount (100 N)
• Protection class IP40

The Z5A Belt-Aligner is a laser-based tool for the exact alignment of belt drives and pulleys. A compact line laser from the ZAT series is mounted in a specially designed holder and projects a red line that runs precisely parallel to the magnetic reference surface. Using the included target markers, drive and idler pulleys can be aligned quickly, safely, and without risk while at a standstill. Proven thousands of times in industrial use, the Z5A stands out for its ease of handling and reliable results. Delivered as a complete set with holder, measuring blocks, battery, and transport case, it offers everything needed for efficient belt alignment.

With the ProBus interface, the ZD500, 1000, and 1500 becomes an integral part of the oscilloscope. All probe gain and offset controls are transparent to the user, making it easier to probe the circuit without concern for which gain setting to choose. When used with a LeCroy digital oscilloscope, no external power supply is required.

• 3/4 length board (1/2 size available w/o GPS input)
• Optional Have Quick synchronization input
• IRIG’s A and B and NASA 36 time code inputs
• 1PPS sync input
• IRIG B output option
• 1PPS and time code inputs are redundant
• Single-slot including GPS option
• Zero latency time reads
• External Event input (optional eight or sixteen inputs)
• Match Time output
• Programmable Heartbeat rate

• Eight ports of 8 I/O bits each
• High current capability for control of external relays, 300 mA sink
• Simulate and receive digital data at up to 2 MHz sample rates
• Selectable output voltages range from 3.3 V to 60 V
• Setup outputs and scan inputs as part of EX1200 measurement sequencing engine

• 16 channel GPS SPS receiver (standard) 
• IRIG B Time Code (standard) 
• HaveQuick/1PPS from external GPS receiver (standard) 
• Temperature Compensated Crystal Oscillator (TCXO) – option 
• Oven Controlled Crystal Oscillator (OCXO) standard 
• Atomic Rubidium Oscillator – option 
• 1PPS 1 Pulse Per Second Signal Time Mark 
• Have Quick Time Code 
• IRIG B Time Code 
• NTP

See "Specifications & Details" tab for more information

• Real-Time Full Bandwidth Data Acquisition
• Versatile – Reconfigurable Front End
• Measure: PM / AM / Baseband / Spurious / Jitter
• Isolated AM / PM
• Automated Residual Measurements
• Outstanding Accuracy

The HA7163A is a heterodyne downconversion system that is designed to seamlessly integrate with Holzworth’s real time phase noise analysis products as a calibrated frequency extension. The HA7163A provides for both absolute and residual (additive) measurements to 50GHz, making it the only solution available on the market for taking accurate additive phase noise measurements at frequencies of greater than 18GHz, without using external mixers.

• LMR Signal Analyzers with Coverage Mapping: P25, P25 Phase 2, DMR (MotoTRBO™), TETRA, NXDN, dPMR, PTC-ITCR, PTC-ACSES, NBFM, FDD & TDD LTE
• Broadband Signal Analyzers: LTE, WiMAX
• Interference Analyzer with Interference Mapping and support for MA2700A Handheld Interference Hunter
• Auto Test and Alignment of Motorola APX P25 mobiles and portables
• Direct measurement of up to 150 watt transmitters
• Spectrum Analyzer: 9 kHz – 1.6 GHz, optional to 6 GHz
• Cable and Antenna Analyzer: 500 kHz – 1.6 GHz, optional to 6 GHz
• Return Loss, VSWR, Insertion Loss, S11 / S21, DTF
• PIM Hunting
• Internal Power Meter, optional External Power Sensor
• Handheld, battery-operated design
• Weighs less than 7.6 lb (including battery)
• Rugged, field-proven design using Anritsu's 9th generation hardware platform
• Daylight viewable color touchscreen display
• Superior Immunity to RF interference
• Remote control via Ethernet
• Standard three-year warranty (battery one-year warranty)