Teledyne DALSA - Retiga CCD Camera Family
This CCD Family includes the R6, the ELECTRO, the LUMO and the MicroPublisher 6, a offering a range of CCDs designed for documentation, electrophysiology, long-exposure and color imaging respectively. These cameras are fast, sensitive CCDs designed for microscopy and scientific research.
Large Field Of View
The Retiga R6, Retiga LUMO and MicroPublisher 6 all delivers a large 16 mm field of view designed to increase throughput and maximize the amount of data captured in a single frame. Image larger samples or increase throughput by imaging multiple cells at once by taking advantage of a larger field of view.
High Resolution
The Retiga R6, Retiga LUMO and MicroPublisher 6 present small 4.54 µm pixels in a 6 megapixel array to maximize the resolving power of your system. The small pixels provide highly detailed images across the imaging plane, which allows for the highest resolution when using lower magnification objectives.
MicroPublisher 6: Color and Fluorescence Imaging
The MicroPublisher 6 delivers highly accurate color images using a Bayer filter array. This CCD camera is also capable of performing high quality fluorescence imaging, a typically challenging task for a color camera. The high quantum efficiency and low noise of the MicroPublisher 6 make monochrome fluorescence imaging equally possible.
Retiga ELECTRO: Advanced Technical Features
The advanced technical features of the Retiga ELECTRO were designed to empower electrophysiologists to image without exogenous noise that pollute recordings. This is accomplished by coupling regulated fanless cooling and external grounding with FPGA-based intelligent features to correct defective pixels. Thanks to a finblade design and advanced software solutions, the Retiga ELECTRO is designed with electrophysiology in mind.
Retiga LUMO: Advanced Technical Features
The advanced technical features of the Retiga LUMO were designed to perform long exposure time experiments by coupling deep cooling with FPGA-based intelligent features. Defective Pixel Correction (DPC) and Dynamic Dark Frame Correction (DDFC) correct hot pixels and remove background for high quality images over difficult long exposures and an ultra low noise readout mode enables exposure times of up to 60 minutes.
Simple Installation
The full range of CCDs in this family deliver data over a simple, versatile and high-speed USB 3.0 digital interface. This standard, accepted interface is present on most modern computers, simplifying connectivity. These CCDs are also supported on the latest Windows operating systems ensuring modern system compatibility.
Models
|
Model Number |
MP |
FOV (Diag. mm) |
FPS |
Pixel Size (μm) |
QE |
Read Noise |
Dark Current |
FWC |
Sensor |
|---|---|---|---|---|---|---|---|---|---|
|
MicroPublisher 6 01-MP6-R-CLR-14-C-OC |
5.9 |
12.5 x 10 mm |
7.1 fps |
4.54 µm |
75% |
6 e⁻ |
0.0007 e⁻/p/s |
19,000 e⁻ |
Sony ICX695 |
|
Retiga ELECTRO 01-ELECTRO-M-14-C-OC |
1.3 |
8.8 x 6.6 mm |
22 fps |
6.45 µm |
75% |
5.5 e⁻ |
0.036 e⁻/p/s |
11,000 e⁻ |
Sony ICX825 |
|
Retiga LUMO 01-RET-LUMO-R-M-16-C |
5.9 |
12.5 x 10 mm |
7.1 fps |
4.54 µm |
75% |
4.5 e⁻ |
0.0004 e⁻/p/s |
27,000 e⁻ |
Sony ICX695 |
|
Retiga R6 01-RET-R6-R-M-14-C-OC |
5.9 |
12.5 x 10 mm |
7.1 fps |
4.54 µm |
75% |
5.7 e⁻ |
0.0007 e⁻/p/s |
19,000 e⁻ |
Sony ICX695 |
More Product Information
- Highest resolution – 12 bits all the time
- More capability – integrates multiple instruments into one
- Comprehensive probe support – supports over 30 probes in 9 categories
- MAUI with OneTouch user interface for intuitive and efficient operation
- Extended Spectral Range
- Capture images from visible light to SWIR (400 nm to 1700 nm) and enhance detection and analysis across various materials and applications.
- Compact and Balanced Design
- The compact housing balances image performance and size. It is ideal for space-constrained environments without compromising image quality.
- GigE Performance and Reliability
- GigE driver performance with the Spinnaker® SDK, Sapera™ Processing, and a powerful Trigger-to-Image Reliability (T2IR) framework.
The FLIR Blackfly S Board Level variants are high performance, machine vision, area scan cameras designed for embedding into tight spaces. Unlike many board level cameras, it boasts a rich feature set applied to the latest CMOS sensors; the same feature set as the cased version. It is ready for integration with proven compatibility with popular SBCs and SOMs. The Blackfly S board level models enable OEMs to develop smaller, lighter, and lower cost solutions with embedded system connectivity and rich features.
The Blackfly S currently has a lead time of four weeks or less. Get the cameras you need – when you need them.
- 2, 4 and 8 channel configurations
- 16-bit vertical resolution
- Sample Rate up to 12,32 GS/s with RF mode
- 16-bit vertical resolution.
- 4 GSample waveform memory per channel
- Up to 5 Vpp Output Voltage and ±2.5 V Baseline Offset (into 50?)
- IP67 ingress protection minimizes dust and debris accumulation for simplified maintenance
- Onboard processing for no-drop image capture and delivery
- Highly robust and reliable Teledyne GigE framework within the Spinnaker® 4 acquisition SDK
- Support for Sapera® Image Processing Library with AI capability
- Approved partner network for a vast selection of industrial camera accessories
- Includes a three-year warranty, access to rich online resources, and world-class technical support
Transmission line probes are a special type of passive probe designed for use at very high frequencies. They replace the high impedance probe cable found in a traditional passive probe with a precision transmission line, with a characteristic impedance that matches the oscilloscope input (50 Ohm). This greatly reduces the input capacitance to a fraction of a picofarad, minimizing the loading of high frequency signals. A matching network at the tip increases the DC input resistance. While they have lower DC input resistance than a traditional passive probe (usually 500 Ohm) to 1kOhm), the input impedance of these probes remains nearly constant over their entire frequency range. A traditional /10 passive probe will have a 10 MOhm) input impedance at DC, however this impedance drops rapidly with frequency, passing below the input impedance of a transmission line probe at less than 100 MHz.
With the ProBus interface, the ZD500, 1000, and 1500 becomes an integral part of the oscilloscope. All probe gain and offset controls are transparent to the user, making it easier to probe the circuit without concern for which gain setting to choose. When used with a LeCroy digital oscilloscope, no external power supply is required.
-
Easy to Use
-
No need to break the circuit or insert a shunt
-
Small form factors for use on crowded boards
-
-
Variety of Applications
-
Bandwidths up to 100 MHz
-
Peak currents up to 700 A
-
Sensitivities down to 1mA/div
-
-
High Precision Measurements
-
Low frequency accuracy of 1%
-
Integrated autozero capability
-
-
Fully Integrated with Teledyne LeCroy Oscilloscope
-
No additonal hardware is required
-
Power is supplied from oscilloscope ProBus connection
-
Automatic display of waveforms in Amps and calculated power traces scaled correctly in Watts
-
Degauss and Autozero directly from oscilloscope user interface
-
-
DCS025 Deskew Calibration Source
-
Provides ability to precisely deskew most voltage probes along with 30, 150 and 500A current probes
-
- Supports PCI Express Rev 2.0 x4 or higher, backwards compatible with PCIe Rev 1.10 slots
- Up to 512MB of high-speed image memory
- Single slot solution with reconfigurable camera control and general purpose input/outputs
Teledyne DALSA
Teledyne DALSA is an international leader in high performance digital imaging and semiconductors with approximately 1000 employees world-wide. Established in 1980 and acquired by Teledyne Technologies in 2011, Teledyne DALSA designs, develops, manufactures, and markets digital imaging products and solutions, in addition to providing semiconductor products and services. Our core competencies are in specialized integrated circuit and electronics technology, software, and highly engineered semiconductor wafer processing.
Teledyne DALSA exists for the long term. Our goal is to build upon our 30 year heritage of developing the world's leading high performance digital imaging and semiconductor solutions and to accelerate our level of innovation. We focus on R&D development but also draw on the capabilities available to us as part of a larger organization. We seek to deliver products and technology that are truly innovative so that we can help our customers succeed.
Contact Details
Teledyne DALSA Headquarters
605 McMurray Road, Waterloo, Ontario, Canada N2V 2E9
Phone: 519-886-6000
Fax: 519-886-8023
Imaging/Machine Vision
Download Line Card
