Overview
Specifications & Details
Datasheets & Downloads
Videos

Near Linear Power Supply
Modular
≥0.95 PFC
Digital control loop technology
High Power Density (3.5 watts/cubic inch)
“Virtual Assets” by:
- Series operation
- Parallel operation
- Combined operation with loads
Simple integration

Manufactured By: AMETEK Programmable Power

More

ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.

Up to 8 mainframes, potentially up to 95 modules, can be controlled via a single controller. The controller communicates to the individual modules via a high speed proprietary bus protocol, providing very high data rates and a high degree of deterministic control. The RFP™ controller communicates to the host controller via an Ethernet LAN connection designed to be compliant with the LAN Extension for Instrumentation ( ™ ) standard, assuring interoperability and ease of integration. RFP™ system modules can be combined via the controller, permitting the creation of “virtual assets” with the voltage/current combinations required for a particular test regime. Creating “virtual assets” reduces the “logistical tail” and total cost of ownership.

Available power modules include

Single slot, 330 Watt programmable DC supplies
- 16V, 20.6A
- 65V, 5.1A
Dual slot, 1kW programmable DC supplies
- 33V, 30A
- 50V, 20A
- 50V, 25A
- 120V, 8.3A
- 450V, 2.3
Triple slot, 875 VA, single phase, programmable AC supply
- Dual range: 280V(rms), 3.5A(rms)
- Dual Range: 140V(rms), 7A(rms)
Triple slot, 500V, programmable electronic DC loads
- 15A, 375 Watt
- 30A, 750 Watt

The mainframe provides internal power distribution, cabling, I/O and power connection and rack mounting for 12-asset slots. The mainframe also supplies the signal and control bus fabric supporting multi-module series/parallel operation, complex triggering, fault I/O and inter-mainframe control infrastructure.

DC High Power Modules General Specifications
Line Regulation	+/- 10% line change
Steady State, Voltage Mode	0.01% of full-scale + 10mV (330W) and 0.03% of full-scale (1kW)
Steady State, Current Mode	0.05% of fullscale (330W) and 0.1% of full-scale (1kW)
Transient, Voltage Mode	Less than 1% of full-scale excursion returning to steady state within 500 micro-sec
Transient, Current Mode	Less than 0.05% of full-scale (330W) and less than 0.1% (1kW)
Remote Sense	Up to 3V load line drop. The drop in the load leads subtracts from the maximum voltage available for the load.
Parallel	Up to six like modules
Series	Up to five like modules for 16V, 65V; up to three like models for 33V, 50V, 120V Float not to exceed 200V (16V, 33V, 50V 120V), 300V (65V), 450V (450V).
Sag/Surge/Hold Up	Sag to 65% of nominal for 450ms at full output power with AC input at ≥200VAC. Surge to 135% of nominal for 450ms at full output with AC input ≤230VAC. 10ms hold up at loss of input.
Remote Programming Connector	9-pin D-sub
Output Connector	Combination signal/power contact subminiature D (Mating connector kit available)
Physical	330W: 4.2 lbs (1.91 Kilograms) 1000W: 8.7 lbs (3.95 Kilograms)
Regulatory	Certified to UL 61010-1, CSA C22.2 No. 61010.1 and IEC/EN 61010-1. Compliance with EN61326 and FCC 21 CFR, Subpart J CE Mark is to EMC and LVD All specifications: 25°±5°C.

Output Voltage and Current
Output Voltage	33V	450V	50V	50V	120V
Output Current	30A	2.3A	20A	25A*	8.3A
Maximum Power	990W	1035W	1000W	1250W*	996W
Mainframe Slots	2	2	2	2	2
Output Rise / Fall Time	20msec	20msec	20msec	20msec	20msec

Output Voltage and Current
RMS	15mV	40mV	20mV	20mV	20mV
Peak-Peak	60mV	200mV	75mV	75mV	75mV

Programming Accuracy
Voltage (0.05% of setpoint +)	16.5mV	225mV	25mV	25mV	c60mV
Current (0.2% of setpoint +)	30mA	2.3mA	20mA	25mA	8.3mA

Temperature Coefficient
Voltage /˚C	3.3mV	45mV	5mV	5mV	12mV
Current /˚C	7.5mA	0.6mA	7.5mA	7.5mA	2.5mA

*1250 Watt module must have an AC input voltage above 188 Vac or DC input above 210 vDC. The module will not operate below the required input line voltage.

All specifications are subject to change

AMETEK ReFlex Power Data Sheet.pdf

AMETEK ReFlex Power Cut Sheet.pdf

Manuals, Software, Drivers and Other

View YouTube Channel

Elgar - ReFlex Power DC High Power Module 1000W DC Power Supply