White Paper

Oscilloscopes

Teledyne LeCroy: All-ETDM 80-Gbaud (160-Gb/s) QPSK Generation and Coherent Detection

A single-polarization 160-Gb/s (80-Gbaud) electronically time-division-multiplexed (ETDM) quadrature phase-shift-keyed (QPSK) signal is generated and coherently detected using two 45-GHz-bandwidth oscilloscope prototypes and offline processing.

Related Topics:

Videos

Teledyne LeCroy: Mixed Signal Oscilloscope - Measurement
Teledyne LeCroy: Most efficient validation of power sequences

Webinars

Pre-Compliance EMC Testing with a Real Time Scope
SI/PI on a Budget Webinar: Five Tricks to Get More out of your Oscilloscope
EMC / ESD Pulse Measurements Using Oscilloscopes Webinar
Fundamentals of Advanced Measurements and Math
4 Practical Real-world Examples of Embedded System Validation and Debug
Oscilloscope Coffee Break Series - Part 3: Getting Your Trigger to Do What You Want
How to Measure Power During Volt-second and Other Short Power Periods
Setting up Your Timebase and Using Memory Correctly Oscilloscope - Coffee Break Webinar Series
Optimizing Your Vertical Gain Oscilloscope - Coffee Break Webinar Series
How to Become an Expert in Automotive Ethernet Testing - Part 4: Debugging PHY Layer Link Communication Learning Lab
What Every Oscilloscope User Should Know About Transmission Lines
Testing Noisy Power Supply Outputs - Oscilloscope Coffee Break Webinar Series
How to Perform Customized Analysis With an Oscilloscope Part One: Fundamentals of Customized Analysis
How to Perform Customized Analysis With an Oscilloscope Part Two: Advanced Customization Examples
USB Type-C® Technologies Webinar Series Part 4: USB Type-C Sideband Physical Layer Testing
SI/PI Measurements on a Budget Webinar Part 4: How to Become an Expert in Power Integrity Testing
Zooming With an Oscilloscope – Zoom Waveforms and Timebase Adjustment
What is Oscilloscope Sample Rate and How Much Do I Need? by Teledyne LeCroy
How Much Memory Do I Need to Use in my Oscilloscope by Teledyne LeCroy
How Can I Reduce Noise on Signals Measured With an Oscilloscope? by Teledyne LeCroy
How is Rise Time Related to Bandwidth in an Oscilloscope? by Teledyne LeCroy
Teledyne LeCroy: How Do I Measure Current on an Oscilloscope Using a Shunt Resistor?
Teledyne LeCroy: How Do I Make a Differential Measurement on an Oscilloscope Using Passive Probes?
Teledyne LeCroy: How Do I Rescale a Sensor to Use With an Oscilloscope?
Teledyne LeCroy: How Do I Make an XY Display on an Oscilloscope?
Teledyne LeCroy: How Do I Make 3-phase Power Measurements with an Oscilloscope?
What are Oscilloscope ADC Effective Bits and ENOB?
High Speed Serial Data Debugging using a Digital Oscilloscope - Part 3
Teledyne LeCroy - What is the Difference Between a Real-time Oscilloscope and a Sampling Oscilloscope?
Teledyne LeCroy - How to Maximize Digital Oscilloscope Signal Integrity
Teledyne LeCroy - How Does an Oscilloscope Probe Affect My Oscilloscope Gain Settings, Accuracy, Noise, and Dynamic Range?
Teledyne Lecroy - Part 7: Getting the Lead Out – Expert Soldering Tips
Teledyne LeCroy - When Do I Need to Deskew Channels or Probes on an Oscilloscope?
Teledyne LeCroy - Oscilloscope Coffee Break Part 9: What is a Digital Phosphor Oscilloscope?
Teledyne LeCroy - Oscilloscope Coffee Break Part 10: How Do I Use Roll Mode on My Oscilloscope?

White Papers

Teledyne LeCroy: Enhanced Sample Rate Mode Measurement Precision
Teledyne LeCroy: Technologies for Very High Bandwidth Real-time Oscilloscopes
Teledyne LeCroy: Using a Digital Oscilloscope for Signal Analysis Including A Practical Example of PLL Characterization
Teledyne LeCroy: Coherent 1200km 6x6 MIMO Experiment using LabMaster
Teledyne LeCroy: Mode-Equalized Raman Gain Experiment using LabMaster