VIAVI - ALT-9000 Radio Altimeter Test Set
-
Fiber optic delay line based test set supports all formats of radio altimeters
-
Portable ruggedized enclosure for flight line or benchtop use
-
Battery operated
-
Simulates static altitudes from 0* ft. to 10,000 ft. in 10 ft. steps (*minimum simulated altitude dependent upon AID and test cable length)
-
+20 dB of power level offset from nominal loop loss value
-
Touch-screen operation
-
Direct-connect to UUT T/R or installed system via antenna couplers
The ALT-9000 provides altitude simulations with true RF time delay and path loss models to test any format of radio altimeter system including Low Probability of Intercept (LPI), Combined Altitude Radar Altimeter (CARA) & Next Generation variants.
The graphical touch screen interface provides intuitive controls and display of parametric measurements including:
- TX Power
- TX Frequency*
- FM Deviation*
- Sweep Rate*
- Pulse Width*
- PRF*
*Dependent upon LRU technology
More Product Information
-
GPS signals simulated: L1, L1C*, L2C*, L5*
-
Galileo signals simulated: E1, E5**, E5a**, E5b**
-
Simultaneous GPS/Galileo simulation
-
WAAS/EGNOS SBAS simulation
-
Static and dynamic simulations via NMEA-0183 File Record and Playback
-
12 channel configuration available with upgrade path (RAIM supported)
-
Programmable space vehicle (SV) parametrics and health
-
User or built-in GPS receiver referenced time and date
-
PVT data available via RS-232
-
User Defined Data Transferable between Linked GPSG units
-
Remote control interface Ethernet
** For tracking of E5 signals some receivers require synchronized E1 transmissions.
-
Operates up to and including 16GTps, PCIe 4.0 data rates
-
Downward compatible with PCIe 1.0, 2.0 and 3.0 data rates of 2.5, 5.0 and 8.0GTps
-
Supports 1 link of 4 lanes, or dual-port operation of 2 links of 2 lanes each
-
Front-end module plugs into system-under-test
-
U.2 NVMe SSD DUT (not supplied) plugs into the Back-end module
-
Adjustable tray clamps and quick-release latch allow for snug fit and hot swap testing
-
Data path uses high-speed linear redrivers to ensure good signal capture with minimal tuning
-
Supplied with high-quality, custom SFF-8764 cables for Analyzer system attachment
-
Supports side-band signal triggering and capture
-
Supplied power brick makes Interposer power independent of host system
-
LEDs give quick indicators of power and status
-
Works with VIAVI Xgig 4K4 and 4K16 PCIe 4.0 Analyzer/Jammer chassis
-
Provides consistent, repeatable capture of link training, negotiation and other data
-
Supports error injection for deep system analysis
-
Supported by Xgig tool suite including Trace Control, Expert and Serialytics
-
Operates up to 16GTps, PCIe 4.0 data rates
-
Downward compatible with PCIe data rates of 2.5, 5.0 and 8.0GTps
-
Supports 1 link of 4 or 8 lanes
-
EDSFF E1.L or E1.S NVMe SSD DUT (not supplied) plugs directly into the Interposer
-
Includes 4 high-quality, mini-SAS HD 4X cables for Analyzer connection
-
Data path uses high-speed linear redrivers to insure good signal capture with little or no tuning
-
Supports Analyzer side-band signal capture and triggering with display in multiple formats
-
The supplied power brick makes interposer power is independent of host system
-
Works together with the VIAVI Xgig 4K4 and 4K16 PCIe 4.0 Analyzer/Jammer chassis
-
Supported by VIAVI Xgig Analyzer tools for trace capture with filter, trigger and more
-
Provides consistent, repeatable capture of link training, equalization negotiation and other data
-
Operates up to 16GTps, PCIe 4.0 data rates
-
Downward compatible with PCIe 1.0, 2.0 and 3.0 data rates of 2.5, 5.0 and 8.0GTps
-
Supports links of up to and including 4-lanes
-
NVMe SSD DUT (not supplied) plugs directly into the Interposer
-
Supplied with two high-performance custom cables for Analyzer attachment
-
Data path uses high-speed linear redrivers to ensure good signal capture with little or no tuning
-
Supports Analyzer side-band signal capture and triggering
-
Provides two differential clock connectors
-
Interposer power is independent of host system
-
A 120/220 AC in, 12V/3A DC output converter is included
-
LEDs give quick indicators of power and status
-
Format: Design based on 4-lane PCIe CEM specification
-
Supported by VIAVI Analyzer tools for trace capture with filter, trigger and more
-
Provides consistent, repeatable capture of link training, negotiation and other data
-
Supports error injection for deep system analysis
-
Supported by Xgig tool suite including Trace Control, Expert and Serialytics
-
Tests FMCW radio altimeters including CDF types
-
Tests pulse radio altimeters (non-pulse compression types)
-
Direct-connect to UUT T/R or to installed system via antenna couplers
-
Full RF loop test allows TX, RX, Antenna or Feeder faults to be identified
-
Multi-channel operation (via additional test sets)
-
Programmable multi-leg climb/descend profiles
-
Large touch-screen display with simple user interface
-
Remote control interface USB/LAN
-
Lightweight and compact about 10 lbs. (4.5 kg)
-
Battery 4 hours plus duration
-
Accurate measurement of 121.5/243 MHz emergency beacon transmitter frequency, output power, modulation (AM). Headphone audio output to monitor swept tone *
-
Accurate measurement of 406 MHz COSPAS/SARSAT emergency beacon transmitter frequency, output power. Decode and display of all location and user protocols *
-
Accurate measurement of HF transmitter, frequency, output power, modulation (AM and SSB USB/LSB) receiver sensitivity
-
Accurate measurement of VHF/UHF transmitter, frequency, output power, modulation (AM and FM and receiver sensitivity)
-
Generation of ARINC 596 Selective Calling Tones
-
Accurate measurement of VHF/UHF antenna and or feeder SWR (Standing Wave Ratio)
-
Simulation of Localizer and Glideslope (CAT I, II and III) signals with variable DDM settings
-
Swept Localizer DDM for coupled Auto Pilot testing (Simultaneous Localizer, Glideslope and Marker signals)
-
Simulation of Marker Beacon, Selectable Airways (Z), Outer and Middle Marker Tones
-
Guided Test capability cuts down total test time
-
Low cost ELT option
-
Frequency counter provides external frequency measurement
-
MORSE CODE provides 1-4 characters transmitted in the VOR and ILS localizer mode
-
Eight or more hours of operation before recharge
-
Automatic power shut-down
-
Ergonomic design
-
Supports link widths up to 16-lanes
-
Operates up to 32GTps, PCIe 5.0 data rates
-
Downward compatible with PCIe 1.0, 2.0, 3.0 and 4.0, and data rates of 2.5, 5.0, 8.0 and 16GTps
-
A top edge 16-lane CEM slot connector accepts all endpoint DUT adapter cards
-
Bottom edge 16-lane PCB finger connector installs into host test system’s 16-lane PCIe slot
-
Data path uses high-speed linear redrivers to ensure good signal capture with minimal tuning effort
-
Supports Analyzer side-band signal triggering and capture via custom cable
-
Interposer power is independent of host system. A 120/220 AC in, 12V/3A DC out converter is included
-
Custom, exchangeable brackets enable secure chassis and endpoint card installations
-
LEDs give quick indication of power and operation
-
Format: Design is based on the 16-lane Card Electro-Mechanical (CEM) specification
-
Size: 230mm deep x 185mm tall x 15mm thick
-
Operates up to 32GTps at PCIe 5.0 data rates
-
Downward compatible with PCIe data rates of 2.5, 5.0, 8.0 and 16.0GTps
-
Supports link widths up to 16-lanes
-
CEM adapter card endpoint DUT devices plug directly into the Test Stand
-
Includes cables for Analyzer connection
-
Supports Analyzer side-band signal capture and triggering with display in multiple formats
-
Data path uses high-speed re-drivers to ensure good signaling
-
Supports automatic link tuning for optimum communication and lowest BER
-
Modular, replaceable 600W power supply powers Test Stand and DUT
-
Supports testing of high-power graphics cards
-
LEDs give quick indicators of power and status
-
Size: Base Pod: 120 x 162 x 30 mm (DxWxH)
-
Works with the VIAVI Xgig5P-PCIe5-X16-PF Analyzer/Exerciser chassis platform
-
Supported by VIAVI Xgig™ Analysis tools for test setup, trace capture, protocol evaluation, etc.
-
Provides consistent, repeatable capture of link training, equalization negotiation and other information
VIAVI
VIAVI is a leading worldwide provider of highly specialized test and measurement equipment and microelectronic solutions.
VIAVI Solutions is proud of our industry-leading network solutions for Telecommunications Service Providers, Equipment Manufacturers, Enterprises, and Entities in fields of Government and Avionics. VIAVI is consistently #1 or #2 in the markets we serve, including: Fiber, Cable, Access, Metro and Transport, RAN-to-Core, LandMobile and Military Radio and Nav/Comm and Transponder. We offer end-to-end network visibility and analytics that help build, test, certify, maintain, and optimize complex physical and virtual networks.
Our optical specialty products division is renown for expertise in anticounterfeiting pigment materials, 3D Sensing, and optical filters – holding #1 positions in those markets as well.
The pioneering spirit at VIAVI continues as we light the path to 5G with innovative test and measurement products, and lead the way with 3D sensing technology.
Contact Details
VIAVI Solutions Inc. Corporate Headquarters
6001 America Center Drive, 6th Floor, San Jose, CA 95002, USA
Phone: +1-408-404-3600
Fax: +1-408-404-4500