Dualos - Fittings - NEO 601F Series
*Approximate Dimensions [inches]
** All adapters ship with 12″ Lanyard and ‘REMOVE BEFORE FLIGHT’ flag
Part Number |
Port Size 1 |
Thread End [1] |
Port Size 2 |
Thread End [2] |
A |
B |
D |
---|---|---|---|---|---|---|---|
NEO 601F-P-04 | 4, 12 | JIC-37 Degree | 4 |
0.4375-20 UNJF Class 3B |
2.13 | 0.48 | - |
NEO 601F-P-05 | 12 | JIC-37 Degree | 5 |
0.5000-20 UNJF Class 3B |
2.13 | 0.48 | - |
NEO 601F-P-06 | 6, 12 | JIC-37 Degree | 6 |
0.5625-18 UNJF Class 3B |
2.18 | 0.49 | - |
NEO 601F-P-08 | 8, 12 | JIC-37 Degree | 8 |
0.7500-16 UNJF Class 3B |
2.30 | 0.56 | - |
NEO 601F-P-10 | 10, 12 | JIC-37 Degree | 10 |
0.8750-14 UNJF Class 3B |
2.44 | 0.66 | - |
NEO 601F-P-12 | 12 | JIC-37 Degree | 12 |
1.0625-12 UNJ Class 3B |
2.52 | 0.70 | - |
NEO 601F-P-16 | 12 | JIC-37 Degree | 16 |
1.3125-12 UNJ Class 3B |
2.74 | 0.79 | - |
NEO 601F-P-20 | 12 | JIC-37 Degree | 20 |
1.6250-12 UNJ Class 3B |
2.87 | 0.98 | - |
More Product Information
-
On-Off power switch
-
20 A Circuit Breaker
-
Inlet - NEMA L6-20
-
Outlets – NEMA L6-20R
-
3ft.
-
(2) fork terminals (current)
-
(1) fork terminals (ground)
-
(2) Shielded Banana (voltage)
-
Ruggedized sensor package, qualified to same rigorous standards applied to electronic gages
-
Integrated temperature compensation FBG sensor
-
Connector protection fittings available for harsh environments
-
Double-ended design supports multiplexing of many sensors on one fiber
-
Patented micro opto-mechanical technology
Our “A” and “W” Series amplifiers have the power to deliver all the field strength you need. With unsurpassed mismatch capabilities and excellent flatness, they provide all the power promised over the entire operating band.
We subject our amplifiers to the harshest conditions just to make sure they give you reliable service and performance over the long haul. We test them under various output VSWR loads to stress them to the limit. The only problem we ran into was that there were no available loads to handle the enormous power up to 80,000 W that our amplifiers deliver. Whereas this would stop most manufacturers, it presented another challenge to our talented designers, and we designed our own. All our RF solid-state amplifiers have modulation capability that will faithfully reproduce AM, FM or Pulse Modulation appearing on the input signal for use in the most demanding EMC applications.
These technologically advanced amplifiers perform beyond the norm, beyond expectations, and way beyond the abilities of other test amplifiers.
These self-contained, broadband, completely solid-state amplifiers are designed for applications requiring the ultimate in output power over a wide instantaneous bandwidth with high gain. Extensive control and status reporting capabilities are available both locally and remotely. Most models feature air-cooled designs while some higher power units feature liquid cooled designs. The touch-screen panels are intuitive, convenient, and easy to use.
-
Ruggedized sensor package, qualified to same rigorous standards applied to electronic gages
-
Integrated temperature compensation FBG sensor
-
Connector protection fittings available for harsh environments
-
Double-ended design supports multiplexing of many sensors on one fiber
-
Two standard gage lengths of 25 and 100 cm
-
P67 rated for protection from dust and water ingress
-
15’ Flexible Power Cord
-
IEC C13 / C14 Connectors
-
3ft.
-
(2) fork terminals (current)
-
(1) fork terminals (ground)
-
(2) Shielded Banana (voltage)
-
Accurate measurement of 121.5/243 MHz emergency beacon transmitter frequency, output power, modulation (AM). Headphone audio output to monitor swept tone *
-
Accurate measurement of 406 MHz COSPAS/SARSAT emergency beacon transmitter frequency, output power. Decode and display of all location and user protocols *
-
Accurate measurement of HF transmitter, frequency, output power, modulation (AM and SSB USB/LSB) receiver sensitivity
-
Accurate measurement of VHF/UHF transmitter, frequency, output power, modulation (AM and FM and receiver sensitivity)
-
Generation of ARINC 596 Selective Calling Tones
-
Accurate measurement of VHF/UHF antenna and or feeder SWR (Standing Wave Ratio)
-
Simulation of Localizer and Glideslope (CAT I, II and III) signals with variable DDM settings
-
Swept Localizer DDM for coupled Auto Pilot testing (Simultaneous Localizer, Glideslope and Marker signals)
-
Simulation of Marker Beacon, Selectable Airways (Z), Outer and Middle Marker Tones
-
Guided Test capability cuts down total test time
-
Low cost ELT option
-
Frequency counter provides external frequency measurement
-
MORSE CODE provides 1-4 characters transmitted in the VOR and ILS localizer mode
-
Eight or more hours of operation before recharge
-
Automatic power shut-down
-
Ergonomic design
Beginning in 2019, AR will be embedding ampwebwARe in all new amplifiers. Once an amplifier is connected to a network and an IP address is set, any other device connected to that network can access the amplifier’s embedded webpage. The features of this embedded webpage include:
- All Information Shown on One Screen
- Simple User Interface
- Allows for Remote Diagnostics
- Monitor Status from Anywhere
- Multiple Simultaneous Browser Connections
- Many Supported Web Browsers
Dualos
Sometimes commercial products just won’t cut it. Dualos supplies the avionic industry with most reliable, precision manufactured hydraulic interface components in the market.
With the quality and assurance that’s expected, Dualos partners with major avionics manufacturers to solve complex engineering and test challenges. A lack of commercially available hydraulic test adapters was the problem. This opportunity laid the foundation in forming Dualos’ Hydraulic Interface Components division a decade ago.
Dualos designs, manufactures and provides logistical support for an entire family of Hydraulic Interface Components.
Contact Details
Dualos
917 Pacific Avenue, Suite 400, Tacoma, WA 98402, USA
Phone: 253-750-5125
Fax: 253-212-3539
Email: sales@dualos.com