Test & Measurement
Products
-
Allows TekProbe interface level II probes to work with any ProBus-equipped Teledyne LeCroy oscilloscope
-
Automatic probe detection
-
Provides all necessary power and offset control to the attached probe
-
Supports probes up to 4 GHz
-
Easy firmware updates
-
Wide variety of probes supported including: Preamplifiers, Current Probes, Single-Ended Active Probes and Differential Active Probes
Transmission line probes are a special type of passive probe designed for use at very high frequencies. They replace the high impedance probe cable found in a traditional passive probe with a precision transmission line, with a characteristic impedance that matches the oscilloscope input (50 Ohm). This greatly reduces the input capacitance to a fraction of a picofarad, minimizing the loading of high frequency signals. A matching network at the tip increases the DC input resistance. While they have lower DC input resistance than a traditional passive probe (usually 500 Ohm) to 5 kOhm), the input impedance of these probes remains nearly constant over their entire frequency range. A traditional /10 passive probe will have a 10 MOhm) input impedance at DC, however this impedance drops rapidly with frequency, passing below the input impedance of a transmission line probe at less than 100 MHz.
-
4 GHz or 6 GHz models
-
Up to 5 Vpk-pk dynamic range with low noise
-
±3 V offset range
-
Deluxe soft carrying case
-
Wide variety of tips and leads
-
Solder-In Lead
-
Positioner (Browser) Tip
-
Adjustable (Browser) Tip
-
Quick Connect Lead
-
HiTemp Solder-In Lead
-
-
Ideal for DDR2, DDR3, LPDDR2
-
Low loading and high imedance for minimal signal disturbance
-
Up to 25 GHz bandwidth (probe + oscilloscope)
-
System rise time as fast as 13 ps (20-80%)
-
Highest bandwidth Solder-In solution (25 GHz)
-
Ultra-compact browser tip (22 GHz)
-
Superior probe impedance minimizes AC loading on device under test (DUT)
-
Carbon-composite browser tips optimizes signal fidelity and loading
-
Probe noise as low as 14 nV/√Hz (1.6 mVrms)
-
Low probe attenuation
-
Large operating voltage range
-
±4 V common mode range
-
±2.5 V offset range
-
2.0 Vpk-pk dynamic range
-
-
Long length Solder-In tip with field replaceable resistors
-
Choice of 8, 10, or 13 GHz bandwidth models
-
3.5 Vpk-pk dynamic range
-
±4 V offset range
-
Ideal for DDR3, DDR4, LPDDR3
-
Deluxe soft carrying case
-
Wide variety of tips and leads
-
Solder-In Lead
-
Positioner (Browser) Tip
-
SMA/SMP Lead
-
Square Pin Lead
-
-
SMA/SMP lead set accessory does not require purchase of a different amplifier
-
Low loading and high imedance for minimal signal disturbance
-
Up to 30 GHz bandwidth and 80 GS/s sample rate
-
The most advanced oscilloscope user interface
-
The industry’s only true hardware 14.1 Gb/s serial trigger
-
Low Jitter Measurement Floor and exceptional timebase stability
-
Comprehensive set of serial data analysis, debug, validation and compliance tools
-
Integrated 50 Ω and 1 MΩ inputs for true connection and probing flexibility
-
Integrated standard and custom measurements and math functions for unrivaled analysis capability
-
Multi-lane serial data eye, jitter and crosstalk analysis
-
Real-time de-embedding, emulation, and equalization
-
HD4096 technology provides 12-bit resolution up to 8 GHz and 20 GS/s
-
Up to 5 Gpts of acquisition memory enables detailed viewing of long events
-
15.6" 1900 x 1080 Full HD capacitive touchscreen
-
New ProBus2 input supports up to 8 GHz bandwidth and direct compatibility with a wide variety of existing ProBus probes - 50Ω and 1MΩ coupling modes support all input types on a single connector
-
MAUI with OneTouch user interface for intuitive and efficient operation
-
Deep toolbox enables and simplifies complex analysis
-
Intuitive navigation to quickly find important features in long waveforms
-
S-parameters DC to 40 GHz, single-ended and mixed-mode
-
Impedance Profile with <1 mm resolution, differential and common-mode
-
Internal, automatic OSLT calibration
-
USB-connected, small, lightweight
-
Flexible display of the measurements
-
Remove effects from fixtures, connectors and cables
-
Emulate eye diagrams with CTLE, DFE and FFE equalization
-
Advanced jitter analysis